LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2009 >> 300 Signature Series >> Repair and Diagnosis >> External Pages >> Different car >> Section 27 (Anti-Lock Brake System - Electrical Diagnostics) >> Abs Electrical Diagnostics >> DTC Troubleshooting >> B1D67-Adjustable Pedal Control Circuit Performance >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2006 Dodge Magnum, 2006 Dodge Charger, and 2006 Chrysler 300. However, it is still accessible from the selected car via links, so may be relevant.
  1. 1)  DTC IS ACTIVE 

    Turn the ignition on.

    With the scan tool, select view DTCs. Record all DTC and DTC Environmental data.

    With the scan tool, clear stored DTCs.

    Cycle the ignition switch off then on.

    Move the Adjustable Pedals Switch forward and rearward several times.

    With the scan tool, select view DTCs.

    Is the status active for this DTC? 

    Yes 

    1. Go To  2).

    No 

    1. Refer to the Adjustable Pedal System intermittent condition test. Refer to APS-INTERMITTENT CONDITION .
  2. 2)  WIRING HARNESS CONNECTOR/TERMINALS 

    Turn the ignition off.

    Disconnect the Memory Seat Module harness connector.

    Disconnect the Adjustable Pedals Motor harness connector.

    Disconnect the Adjustable Pedals Sensor harness connector.

    Inspect the wiring harness, connectors and terminals.

    Were any problems found? 

    Yes 

    1. Repair as necessary.
    2. Perform APS VERIFICATION TEST .

    No 

    1. Go To  3).
  3. 3)  ADJUSTABLE PEDALS ASSEMBLY 

    Turn the ignition off.

    Inspect the Adjustable Pedals Assembly for a condition that would cause the motor to stick or stall.

    Were any problems found? 

    Yes 

    1. Replace the Adjustable Pedals Assembly in accordance with the Service Information.
    2. Perform APS VERIFICATION TEST .

    No 

    1. Go To  4).
  4. 4)  (P205) ADJUSTABLE PEDALS MOTOR FORWARD CIRCUIT OPEN OR HIGH RESISTANCE 
    Fig 1: Checking Adjustable Pedals Motor Forward Circuit For Open Or High Resistance
    GC0014439Courtesy of DAIMLERCHRYSLER CORP.

    Connect a jumper wire between the (P205) Adjustable Pedals Motor Forward circuit and ground at the Adjustable Pedals Motor harness connector.

    Using a 12-volt test light connected to 12-volts, check the (P205) Adjustable Pedals Motor Forward circuit at the Memory Seat Module harness connector.

    NOTE: The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.

    Is the test light illuminated and bright? 

    Yes 

    1. Go To  5).

    No 

    1. Repair the (P205) Adjustable Pedals Motor Forward circuit for an open circuit or high resistance.
    2. Perform APS VERIFICATION TEST .
  5. 5)  (P206) ADJUSTABLE PEDALS MOTOR REARWARD CIRCUIT OPEN CIRCUIT OR HIGH RESISTANCE 
    Fig 2: Checking Adjustable Pedals Motor Rearward Circuit (P206) For Open Or High Resistance
    GC0014440Courtesy of DAIMLERCHRYSLER CORP.

    Connect the jumper wire between the (P206) Adjustable Pedals Motor Rearward circuit and ground at the Adjustable Pedals Motor harness connector.

    Using a 12-volt test light connected to 12-volts, check the (P206) Adjustable Pedals Motor Rearward circuit at the Memory Seat Module harness connector.

    NOTE: The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.

    Is the test light illuminated and bright? 

    Yes 

    1. Go To  6).

    No 

    1. Repair the (P206) Adjustable Pedals Motor Rearward circuit for an open.
    2. Perform APS VERIFICATION TEST .
  6. 6)  (G914) SENSOR RETURN CIRCUIT OPEN OR HIGH RESISTANCE 
    Fig 3: Checking Adjustable Pedals Sensor Return Circuit For Open Or High Resistance
    GC0014441Courtesy of DAIMLERCHRYSLER CORP.

    Connect the jumper wire between the (G914) Sensor Return circuit and ground at the Adjustable Pedals Motor harness connector.

    Using a 12-volt test light connected to 12-volts, check the (G914) Sensor Return circuit at the Memory Seat Module harness connector.

    NOTE: The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.
    NOTE: Remove the jumper wire before proceeding to the next test.

    Is the test light illuminated and bright? 

    Yes 

    1. Go To  7).

    No 

    1. Repair the (G914) Sensor Return circuit for an open.
    2. Perform APS VERIFICATION TEST .
  7. 7)  ADJUSTABLE PEDALS MOTOR 
    Fig 4: Checking Adjustable Pedals Motor
    GC0014442Courtesy of DAIMLERCHRYSLER CORP.

    Turn the ignition off.

    Disconnect the Adjustable Pedals Motor harness connector.

    Measure the resistance between the (P205) Adjustable Pedals Motor Forward circuit and the (P206) Adjustable Pedals Motor Rearward circuit at the terminals of the Adjustable Pedals Motor.

    Is the resistance below 100.0 ohms? 

    Yes 

    1. Replace and reprogram the Memory Seat Module in accordance with the Service Information.
    2. Perform APS VERIFICATION TEST .

    No 

    1. Replace the Adjustable Pedals Motor in accordance with the Service Information.
    2. Perform APS VERIFICATION TEST .
scientia non olet · About LEMON Manuals