LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2009 >> 300 Signature Series >> Repair and Diagnosis >> External Pages >> Different car >> Section 248 ((HVAC Systems - Electrical Diagnostics)) >> HVAC - Electrical Diagnostics >> DTC Troubleshooting >> DTC 72: Short Too Complex (MTC) >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2008 Dodge Magnum, 2008 Dodge Charger, and 2008 Chrysler 300. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK THE (C266) MODE DOOR DRIVER CIRCUIT, (C66) MODE DOOR COMMON DRIVER CIRCUIT, (C255) LEFT BLEND DOOR DRIVER CIRCUIT, (C55) LEFT BLEND DOOR COMMON DRIVER CIRCUIT, (C268) RECIRCULATION DOOR DRIVER CIRCUIT, & (C68) RECIRCULATION DOOR COMMON DRIVER CIRCUIT FOR A SHORT TO VOLTAGE 
    Fig 1: Checking Mode Door, Mode Door Common, Left Blend Door, Left Blend Door Common, Recirculation Door & Recirculation Door Common Driver Circuits For A Short To Voltage
    GC0039718Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Disconnect the A/C Heater Control C2 harness connector.

    Turn the ignition on.

    Measure the voltage of the (C266) Mode Door Driver circuit, (C66) Mode Door Common Driver circuit, (C255) Left Blend Door Driver circuit, (C55) Left Blend Door Common Driver circuit, (C268) Recirculation Door Driver circuit, and the (C68) Recirculation Door Common Driver circuit.

    Is the voltage above 0.2 volts on any of the circuits? 

    Yes 

    1. Repair all circuits with voltage above 0.2 volts for a short to voltage.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To step  2.
  2. CHECK THE (C266) MODE DOOR DRIVER CIRCUIT, (C66) MODE DOOR COMMON DRIVER CIRCUIT, (C255) LEFT BLEND DOOR DRIVER CIRCUIT, (C55) LEFT BLEND DOOR COMMON DRIVER CIRCUIT, (C268) RECIRCULATION DOOR DRIVER CIRCUIT, & (C68) RECIRCULATION DOOR COMMON DRIVER CIRCUIT FOR A SHORT TO GROUND 
    Fig 2: Checking Mode Door, Mode Door Common, Left Blend Door, Left Blend Door Common, Recirculation Door & Recirculation Door Common Driver Circuits For A Short To Ground
    GC0039719Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Measure the resistance of the (C266) Mode Door Driver circuit, (C66) Mode Door Common Driver circuit, (C255) Left Blend Door Driver circuit, (C55) Left Blend Door Common Driver circuit, (C268) Recirculation Door Driver circuit, and the (C68) Recirculation Door Common Driver circuit between ground and the A/C Heater Control C2 harness connector.

    Is the resistance below 10k ohms on any of the circuits? 

    Yes 

    1. Repair all circuits with a resistance below 10k ohms for a short to ground.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To step  3.
  3. CHECK THE (C266) MODE DOOR DRIVER CIRCUIT FOR A SHORT TO THE (C255) LEFT BLEND DOOR DRIVER CIRCUIT, (C55) LEFT BLEND DOOR COMMON DRIVER CIRCUIT, (C268) RECIRCULATION DOOR DRIVER CIRCUIT, & THE (C68) RECIRCULATION DOOR COMMON DRIVER CIRCUIT 
    Fig 3: Checking Mode Door Driver (B) Circuit For Short To Other Door Driver Circuit(s)
    GC0013816Courtesy of CHRYSLER LLC

    Measure the resistance between the (C266) Mode Door Driver circuit and the (C255) Left Blend Door Driver circuit, (C55) Left Blend Door Common Driver circuit, (C268) Recirculation Door Driver circuit, and the (C68) Recirculation Door Common Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 10k ohms on any of the circuits? 

    Yes 

    1. Repair all circuits with a resistance below 10k ohms for a short to the (C266) Mode Door Driver circuit.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To step  4.
  4. CHECK THE (C66) MODE DOOR COMMON DRIVER CIRCUIT FOR A SHORT TO THE (C255) LEFT BLEND DOOR DRIVER CIRCUIT, (C55) LEFT BLEND DOOR COMMON DRIVER CIRCUIT, (C268) RECIRCULATION DOOR DRIVER CIRCUIT, & THE (C68) RECIRCULATION DOOR COMMON DRIVER CIRCUIT 
    Fig 4: Checking Mode Door Driver (A) Circuit & Other Door Driver Circuit(s)
    GC0013815Courtesy of CHRYSLER LLC

    Measure the resistance between the (C66) Mode Door Common Driver circuit and the (C255) Left Blend Door Driver circuit, (C55) Left Blend Door Common Driver circuit, (C268) Recirculation Door Driver circuit, and the (C68) Recirculation Door Common Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 10k ohms on any of the circuits? 

    Yes 

    1. Repair all circuits with a resistance below 10k ohms for a short to the (C66) Mode Door Common Driver circuit.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To step  5.
  5. CHECK THE (C255) LEFT BLEND DOOR DRIVER CIRCUIT FOR A SHORT TO THE (C268) RECIRCULATION DOOR DRIVER CIRCUIT & THE (C68) RECIRCULATION DOOR COMMON DRIVER CIRCUIT 
    Fig 5: Checking Left Blend Door Driver (B) Circuit For Short To Other Door Driver Circuit(s)
    GC0039707Courtesy of CHRYSLER LLC

    Measure the resistance between the (C255) Left Blend Door Driver circuit and the (C268) Recirculation Door Driver circuit and the (C68) Recirculation Door Common Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 10k ohms on any of the circuits? 

    Yes 

    1. Repair all circuits with a resistance below 10k ohms for a short to the (C255) Left Blend Door Driver circuit.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To step  6.
  6. CHECK THE (C55) LEFT BLEND DOOR COMMON DRIVER CIRCUIT FOR A SHORT TO THE (C268) RECIRCULATION DOOR DRIVER CIRCUIT & THE (C68) RECIRCULATION DOOR COMMON DRIVER CIRCUIT 
    Fig 6: Checking Left Blend Common Driver (A) Circuit For Short To Other Door Driver Circuit(s)
    GC0039708Courtesy of CHRYSLER LLC

    Measure the resistance between the (C55) Left Blend Door Common Driver circuit and the (C268) Recirculation Door Driver circuit and the (C68) Recirculation Door Common Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 10k ohms on any of the circuits? 

    Yes 

    1. Repair all circuits with a resistance below 10k ohms for a short to the (C55) Left Blend Door Common Driver circuit.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To step  7.
  7. CHECK THE MODE DOOR ACTUATOR CIRCUIT RESISTANCE 
    Fig 7: Checking Mode Door Actuator Circuit Resistance
    GC0013817Courtesy of CHRYSLER LLC

    Measure the resistance between the (C66) Mode Door Common Driver Circuit and the (C266) Mode Door Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 30.0 ohms? 

    Yes 

    1. Go To step  8.

    No 

    1. Go To step  9.
  8. CHECK THE (C66) MODE DOOR COMMON DRIVER CIRCUIT FOR A SHORT TO THE (C266) MODE DOOR DRIVER CIRCUIT 
    Fig 8: Checking Mode Door Actuator Circuit Resistance
    GC0013817Courtesy of CHRYSLER LLC

    Disconnect the Mode Door Actuator harness connector.

    Measure the resistance between the (C66) Mode Door Common Driver Circuit and the (C266) Mode Door Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 10k ohms? 

    Yes 

    1. Repair the (C66) Mode Door Common Driver Circuit for a short to the (C266) Mode Door Driver circuit.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Replace the Mode Door Actuator in accordance with the Service Information.
    2. Perform BODY VERIFICATION TEST - VER 1 .
  9. CHECK THE LEFT BLEND DOOR ACTUATOR CIRCUIT RESISTANCE 
    Fig 9: Checking Left Blend Door Actuator Circuit Resistance
    GC0013826Courtesy of CHRYSLER LLC

    Measure the resistance between the (C55) Left Blend Door Common Driver Circuit and the (C255) Left Blend Door Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 30.0 ohms? 

    Yes 

    1. Go To step  10.

    No 

    1. Go To step  11.
  10. CHECK THE (C55) LEFT BLEND DOOR COMMON DRIVER CIRCUIT FOR A SHORT TO THE (C255) LEFT BLEND DOOR DRIVER CIRCUIT 
    Fig 10: Checking Left Blend Door Actuator Circuit Resistance
    GC0013826Courtesy of CHRYSLER LLC

    Disconnect the Left Blend Door Actuator harness connector.

    Measure the resistance between the (C55) Left Blend Door Common Driver Circuit and the (C255) Left Blend Door Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 10k ohms? 

    Yes 

    1. Repair the (C55) Left Blend Door Common Driver Circuit for a short to the (C255) Left Blend Door Driver circuit.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Replace the Left Blend Door Actuator in accordance with the Service Information.
    2. Perform BODY VERIFICATION TEST - VER 1 .
  11. CHECK THE RECIRCULATION DOOR ACTUATOR CIRCUIT RESISTANCE 
    Fig 11: Measuring Resistance Between Recirculation Door Common Driver & Recirculation Door Driver Circuits
    GC0039709Courtesy of CHRYSLER LLC

    Measure the resistance between the (C68) Recirculation Door Common Driver Circuit and the (C268) Recirculation Door Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 30.0 ohms? 

    Yes 

    1. Go To step  12.

    No 

    1. Go To step  13.
  12. CHECK THE (C68) RECIRCULATION DOOR COMMON DRIVER CIRCUIT FOR A SHORT TO THE (C268) RECIRCULATION DOOR DRIVER CIRCUIT 
    Fig 12: Measuring Resistance Between Recirculation Door Common Driver & Recirculation Door Driver Circuits
    GC0039709Courtesy of CHRYSLER LLC

    Disconnect the Recirculation Door Actuator harness connector.

    Measure the resistance between the (C68) Recirculation Door Common Driver Circuit and the (C268) Recirculation Door Driver circuit in the A/C Heater Control C2 harness connector.

    Is the resistance below 10k ohms? 

    Yes 

    1. Repair the (C68) Recirculation Door Common Driver Circuit for a short to the (C268) Recirculation Door Driver circuit.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Replace the Recirculation Door Actuator in accordance with the Service Information.
    2. Perform BODY VERIFICATION TEST - VER 1 .
  13. VERIFY THAT THE FAULT IS STILL PRESENT 

    Reconnect the A/C Heater Control C2 harness connector.

    Turn the ignition on.

    Actuate the Clear DTC function by performing the following:

    • Turn the blower control on.
    • Press the A/C mode switch down, turn the blower control to off, wait until both LEDs illuminate (approximately 5 seconds) and then release the A/C mode switch.
    • When the A/C status indicator begins displaying DTCs, set the Mode switch to the floor position, simultaneously press the A/C mode switch and the EBL mode switch down until both LEDs start flashing (approximately 5 seconds) and then release the mode switches. Stored DTCs will clear from memory in approximately two seconds.

    Turn the ignition off, wait 10 seconds, and turn the ignition on.

    Actuate the Actuator Circuit Test / Door Calibration Function by performing the following:

    • Turn the blower control off.
    • Press and hold the EBL mode switch down and then turn the blower control on. Continue to hold the EBL mode switch down until the EBL status indicator begins flashing. Then, release the EBL mode switch. While the test / function is running, the EBL status indicator will flash once per second. If the test / function passes, the EBL status indicator will stop flashing. If the test / function fails, the A/C and EBL status indicators will flash alternately. Allow the test / function to run to completion before proceeding.

    Actuate the Display DTC function by performing the following:

    • Turn the blower control on.
    • Press the A/C mode switch down, turn the blower control to off, wait until both LEDs illuminate (approximately 5 seconds) and then release the A/C mode switch.
    NOTE: The A/C status indicator displays active DTCs when the EBL status indictor is not illuminated and stored DTCs when the EBL status indicator is illuminated.

    Read DTCs from the A/C status indictor.

    Does the A/C status indicator display DTC 72? 

    Yes 

    1. Replace the A/C Heater Control in accordance with the Service Information.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Using the wiring diagram as a guide, inspect the wiring and connectors for conditions causing an intermittent short that set the original fault. Repair as necessary. Then, if present, diagnose and repair all other DTCs. Refer to DIAGNOSTIC CODE INDEX  for a complete list of HVAC related symptoms.
    2. Perform BODY VERIFICATION TEST - VER 1 .
scientia non olet · About LEMON Manuals