LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2009 >> 300 Signature Series >> Repair and Diagnosis >> External Pages >> Different car >> Section 239 (Electronic Control Modules - Electrical Diagnostics) >> Electronic Control Modules - Electrical Diagnostics >> DTC Troubleshooting >> U1107-Ecu In Single-Wire Mode >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2008 Dodge Magnum, 2008 Dodge Charger, and 2008 Chrysler 300. However, it is still accessible from the selected car via links, so may be relevant.
  1. TEST FOR INTERMITTENT CONDITION 

    Turn the ignition on.

    With the scan tool, record and erase TIPM DTC's.

    Cycle the ignition from on to off 3 times.

    Turn the ignition on.

    With the scan tool, read active TIPM DTC's.

    Does the scan tool display this DTC as active? 

    Yes 

    1. Go To  2.

    No 

    1. The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
  2. ANY CAN B BUS MODULE- INTERNAL FAULT 

    Turn the ignition off.

    With the scan tool, monitor the active TIPM DTCs.

    While monitoring the scan tool, disconnect each CAN B Bus module one at a time.

    NOTE: When performing the above step, turn the ignition off (wait one minute) before disconnecting any module. When the module is disconnected turn the ignition on.
    NOTE: This is to determine if the fault is internal within a module.

    Check for this DTC to become active after disconnecting each CAN B Bus module the vehicle is equipped with.

    NOTE: If the DTC becomes stored when a particular CAN B Bus module is disconnected, that module is causing the DTC to set.

    With all the CAN B Bus modules disconnected did the TIPM still set this DTC as active? 

    Yes 

    1. Go To  3.

    No 

    1. Replace the module that when disconnected caused the DTC to become stored.
    2. Perform BODY VERIFICATION TEST - VER 1 .
  3. (D55) CAN B BUS (+) CIRCUIT FOR A SHORT TO VOLTAGE 
    Fig 1: Measuring Voltage Between (D55) CAN B Bus (+) Circuit & Ground
    GC0070082Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Disconnect the Totally Integrated Power Module C1 harness connector.

    NOTE: Ensure each CAN B Bus module is disconnected at this time.

    Turn the ignition on.

    Measure the voltage between the (D55) CAN B Bus (+) circuit and ground.

    Is the voltage above 10.0 volts? 

    Yes 

    1. Repair the (D55) CAN B Bus (+) circuit for a short to voltage.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To  4.
  4. (D54) CAN B BUS (-) CIRCUIT FOR A SHORT TO VOLTAGE 
    Fig 2: Measuring Voltage Between (D54) CAN B Bus (-) Circuit & Ground
    GC0070083Courtesy of CHRYSLER LLC
    NOTE: Ensure each CAN B Bus module is disconnected at this time.

    Measure the voltage between the (D54) CAN B Bus (-) circuit and ground.

    Is the voltage above 10.0 volts? 

    Yes 

    1. Repair the (D54) CAN B Bus (-) circuit for a short to voltage.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To  5.
  5. (D55) CAN B BUS (+) CIRCUIT FOR A SHORT TO GROUND 
    Fig 3: Measuring Resistance Between Ground & (D55) CAN B Bus (+) Circuit
    GC0070084Courtesy of CHRYSLER LLC

    Turn the ignition off.

    NOTE: Ensure each CAN B Bus module is disconnected at this time.

    Measure the resistance between ground and the (D55) CAN B Bus (+) circuit.

    Is the resistance above 1000.0 ohms? 

    Yes 

    1. Go To  6.

    No 

    1. Repair the (D55) CAN B Bus (+) circuit for a short to ground.
    2. Perform BODY VERIFICATION TEST - VER 1 .
  6. (D54) CAN B BUS (-) CIRCUIT FOR A SHORT TO GROUND 
    Fig 4: Measuring Resistance Between Ground & (D54) CAN B Bus (-) Circuit
    GC0070085Courtesy of CHRYSLER LLC
    NOTE: Ensure each CAN B Bus module is disconnected at this time.

    Measure the resistance between ground and the (D54) CAN B Bus (-) circuit.

    Is the resistance above 1000.0 ohms? 

    Yes 

    1. Go To  7.

    No 

    1. Repair the (D54) CAN B Bus (-) circuit for a short to ground.
    2. Perform BODY VERIFICATION TEST - VER 1 .
  7. (D55) CAN B BUS (+) CIRCUIT SHORTED TO THE (D54) CAN B BUS (-) CIRCUIT 
    Fig 5: Measuring Resistance Between (D55) CAN B Bus (+) Circuit & (D54) CAN B Bus (-) Circuit
    GC0070086Courtesy of CHRYSLER LLC

    Measure the resistance between the (D55) CAN B Bus (+) circuit and (D54) CAN B Bus (-) circuit.

    NOTE: Ensure each CAN B Bus module is disconnected at this time.

    Is any resistance present? 

    Yes 

    1. Repair the (D55) CAN B Bus (+) circuit for a short to the (D54) CAN B Bus (-) circuit.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To  8.
  8. (D55) CAN B BUS (+) CIRCUIT OPEN 
    Fig 6: Measuring Resistance Of (D55) CAN B Bus (+) Circuit Between TIPM Connector & Cluster Connector
    GC0070094Courtesy of CHRYSLER LLC

    Measure the resistance of the (D55) CAN B Bus (+) circuit between the TIPM connector and the Cluster connector.

    Is the resistance above 10.0 ohms? 

    Yes 

    1. Repair the (D55) CAN B Bus (+) circuit for an open or high resistance.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Go To  9.
  9. (D54) CAN B BUS (-) CIRCUIT OPEN 
    Fig 7: Measuring Resistance Of (D54) CAN B Bus (-) Circuit Between TIPM Connector & Cluster Connector
    GC0070095Courtesy of CHRYSLER LLC

    Measure the resistance of the (D54) CAN B Bus (-) circuit between the TIPM connector and the Cluster connector.

    Is the resistance above 10.0 ohms? 

    Yes 

    1. Repair the (D54) CAN B Bus (-) circuit for an open or high resistance.
    2. Perform BODY VERIFICATION TEST - VER 1 .

    No 

    1. Replace and program the Totally Integrated Power Module in accordance with the service information.
    2. Perform BODY VERIFICATION TEST - VER 1 .
scientia non olet · About LEMON Manuals