LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2009 >> 300 Signature Series >> Repair and Diagnosis >> External Pages >> Different car >> Section 233 (Differential & Driveline) >> Shaft-Half (Rear) >> Removal >> Half Shaft - Rear

Half Shaft - Rear

WARNING: This page is about a different car, the 2008 Dodge Magnum, 2008 Dodge Charger, and 2008 Chrysler 300. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: This procedure requires the compression of the rear suspension to ride height. A drive-on hoist should be used. If a drive-on hoist is not used, screw-style under-hoist jack stands are required to compress the rear suspension, facilitating rear halfshaft removal.
NOTE: Halfshaft inner and outer boots are not serviceable separately. Boot replacement requires entire shaft assembly replacement.
CAUTION: Unequal-length halfshafts are used. The left halfshaft is shorter than the right, and it is necessary to identify and tag halfshafts upon removal to ensure proper installation.
CAUTION: Never grasp halfshaft assembly by the inner or outer boots. Doing so may cause the boot to pucker or crease, reducing the service life of the boot and joint. Avoid over angulating or stroking the C/V joints when handling the halfshaft.
Fig 1: Rear Axle Drain Plug
GC0014175Courtesy of CHRYSLER LLC
  1. With vehicle in neutral, position and raise vehicle on hoist.
  2. Using 14mm hex, remove axle drain plug (1) and drain rear axle fluid into container suitable for fluid reuse.
  3. Install drain plug (1) and torque to:
    1. 198 Axle: 60 N.m (44 ft. lbs.)
    2. 210 Axle: 50 N.m (37 ft. lbs.)
    Fig 2: Identifying Clamps & Rear Exhaust System
    GC0012972Courtesy of CHRYSLER LLC
  4. Remove rear exhaust system (2) on V8-equipped models.
    Fig 3: Tire And Wheel Mounting
    GC0012971Courtesy of CHRYSLER LLC
  5. Remove wheel/tire assembly (1) from sides that shaft is to be removed.
    Fig 4: Identifying Hub Nut
    GC0012982Courtesy of CHRYSLER LLC
  6. Remove wheel hub nut (1) and discard.
    Fig 5: Alignment Marks At Shaft And Flange
    GC0012988Courtesy of CHRYSLER LLC
  7. Apply alignment index marks (3) to the propeller shaft rubber coupler (1) and axle flange (2).
    Fig 6: Propeller Shaft At Rear Axle Flange
    GC0012989Courtesy of CHRYSLER LLC
  8. Remove three propeller shaft coupler-to-axle flange bolt/nuts.
    Fig 7: Removing Halfshaft - V6
    GC0014178Courtesy of CHRYSLER LLC
  9. Using suitable screwdriver (1), partially disengage halfshaft(s) (2) from axle assembly.
    Fig 8: Supporting Rear Axle With Jack Stands Transmission Jack
    GC0014128Courtesy of CHRYSLER LLC
  10. If a drive-on hoist is used, position transmission jack (1) to rear axle assembly. If a drive-on hoist is not used, compress rear suspension using screw-style under-hoist jack stands (2), then position transmission jack to rear axle assembly.
    Fig 9: Rear Axle Forward Mount Isolator & Bolt/Nut
    GC0014179Courtesy of CHRYSLER LLC
  11. Remove rear axle forward mount isolator (1) bolt/nut (2).
    Fig 10: Rear Axle-to-Crossmember Bolts
    GC0012984Courtesy of CHRYSLER LLC
    CAUTION: Access to rear axle-to-crossmember bolts is best achieved by use of short socket and a flexible-head ratchet.
  12. Remove two rear axle-to-crossmember bolts (1).
    Fig 11: Propeller Shaft Supported
    GC0014181Courtesy of CHRYSLER LLC
  13. Carefully lower rear axle. While lowering axle, separate propeller shaft from axle and support with suitable rope or wire (1).
    Fig 12: Halfshaft Removal/Installation
    GC0014180Courtesy of CHRYSLER LLC
    CAUTION: Unequal-length halfshafts are used. The left halfshaft is shorter than the right, and it is necessary to identify and tag halfshafts upon removal to ensure proper installation.
  14. Lower axle just enough to remove halfshafts one at a time. Shift axle assembly in one direction, compressing one halfshaft while removing the other (1). Use caution to protect axle seal and journal.
    Fig 13: Halfshaft Isolation Washer
    GC0014041Courtesy of CHRYSLER LLC
    CAUTION: Never grasp halfshaft assembly by the inner or outer boots. Doing so may cause the boot to pucker or crease, reducing the service life of the boot and joint. Avoid over angulating or stroking the C/V joints when handling the halfshaft.
    CAUTION: Use care while handling/storing halfshaft assembly. Damage to the slinger can result from improper handling. If slinger gets bent or damaged, straighten slinger to avoid contact with axle seal assembly.
  15. Remove halfshaft from hub. Remove and inspect rubber isolation washer (1). Discard washer if rubber surfaces are worn away. Repeat on other side if necessary.
    Fig 14: Axle Seal Removal
    GC0014182Courtesy of CHRYSLER LLC
  16. Remove axle seals (2) using suitable screwdriver.
scientia non olet · About LEMON Manuals