Diagnostic Test

DTC IS ACTIVE
1. Ignition on, engine not running.
2. With the scan tool, Clear DTCs in the Engine Control Module (ECM).
3. Crank the engine for five seconds.
4. With the scan tool, select View DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go to step 2
  No
  - Perform the CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure.
(T752) ENGINE STARTER MOTOR RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE

Fig 1: Checking Engine Starter Motor Relay Control Circuit For Short To Voltage
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Remove the Starter Relay.
3. Disconnect the Engine Control Module harness connector.
4. Remove the ASD Relay.
5. Connect a jumper wire between cavity 30 and cavity 87 of the ASD Relay Connector.
6. Turn the ignition on.
7. Measure the voltage of the (T752) Engine Starter Motor Relay Control circuit in the Starter Relay connector.
  Is there any voltage present?
  
  Yes
  - Repair the (T752) Engine Starter Motor Relay Control circuit for a short to voltage.
  - Perform the ECM Verification Test.
  No
  - Go To 3
(T752) ENGINE STARTER MOTOR RELAY CONTROL CIRCUIT SHORTED TO THE (T751) FUSED IGNITION SWITCH OUTPUT (START) CIRCUIT

Fig 2: Checking Engine Starter Motor Relay Control Circuit For Short To Fused Ignition Switch Output (Start) Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Remove the jumper wire and install the ASD relay.
3. Measure the resistance between the (T752) Engine Starter Motor Relay Control circuit and the (T751) Fused Ignition Switch Output (START) circuit in the Starter Relay connector.
  Is the resistance above 10.0 Ohms?
  
  Yes
  - Go To 4
  No
  - Repair the (T752) Engine Starter Motor Relay Control circuit for a short to the (T751) Fused Ignition Switch Output (START) circuit.
  - Perform the ECM Verification Test.
(T752) ENGINE STARTER MOTOR RELAY CONTROL CIRCUIT OPEN OR HIGH RESISTANCE

Fig 3: Checking Engine Starter Motor Relay Control Circuit For Open Or High Resistance
Courtesy of CHRYSLER LLC
1. Measure the resistance of the (T752) Engine Starter Motor Relay Control circuit between the Starter Relay connector and the Engine Control Module (ECM) harness connector.
  Is the resistance below 10.0 Ohms?
  
  Yes
  - Go To 5
  No
  - Repair the (T752) Engine Starter Motor Relay Control circuit for an open circuit or high resistance.
  - Perform the ECM Verification Test.
STARTER RELAY
1. Connect the Engine Control Module (ECM) harness connector.
2. Install a known good relay in place of the vehicle's Starter Relay.
3. Turn the ignition on.
4. With the scan tool, Clear DTCs.
5. Crank the engine for five seconds.
6. With the scan tool, select View DTCs.
  Is the status active for this DTC?
  
  Yes
  - Go To 6
  No
  - Replace the Starter Relay in accordance with the Service Information.
  - Perform the ECM Verification Test.
ENGINE CONTROL MODULE (ECM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Starter Relay and the Engine Control Module (ECM).
2. Look for any chafed, pierced, pinched, or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals.
4. Refer to any Technical Service Bulletins that may apply.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the ECM Verification Test.
  No
  - Replace the Engine Control Module (ECM) in accordance with the Service Information.
  - Perform the ECM Verification Test.