Diagnostic Test

TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
  NOTE: Ensure the IOD fuse is installed and battery voltage is between 10.0 and 16.0 volts.
  
  NOTE: Ensure the scan tool is updated to the latest software.
  
  NOTE: If the scan tool displays any error messages involving the Diagnostic CAN C circuits, diagnose and repair the error message before proceeding. See Diagnostic Test .
  
  NOTE: A loss of communication with the TIPM can cause the ECU View button on the scan tool to be inoperative (not highlighted).
2. With the scan tool, attempt to select ECU View.
  Can the scan tool communicate with the TIPM?
  
  Yes
  - The no response condition is not present at this time. Using the appropriate wiring diagram as a guide, inspect the wiring for chafed, pierced, pinched, and partially broken wires and the wiring harness connectors for broken, bent, pushed out, and corroded terminals.
  No
  - Go to Step 2.
FUSED B (+) CIRCUITS OPEN AT TIPM
1. Disconnect the scan tool from the DLC.
2. Using a 12-volt test light connected to ground, and using the appropriate wiring diagram as a guide, check all Fused B (+) circuits at the TIPM.
  Does the test light illuminate brightly for each circuit?
  
  Yes
  - Go to Step 3.
  No
  - Repair the Fused B(+) circuit for an open or short.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
FUSED IGNITION SWITCH OUTPUT CIRCUITS OPEN AT TIPM
1. Turn the ignition on.
2. Using a 12-volt test light connected to ground, and using the appropriate wiring diagram as a guide, check each Fused Ignition Switch Output circuit at the TIPM.
  Does the test light illuminate brightly for each circuit?
  
  Yes
  - Go to Step 4.
  No
  - Repair the Fused Ignition Switch Output circuit for an open.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
GROUND CIRCUITS OPEN AT TIPM
1. Turn the ignition off.
2. Using a 12-volt test light connected to 12-volts, and using the appropriate wiring diagram as a guide, check all ground circuits at the TIPM.
  Does the test light illuminate brightly on each circuit?
  
  Yes
  - Go to Step 5.
  No
  - Repair the ground circuit that did not light the test light for an open.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
CHECK FOR (D52) DIAGNOSTIC CAN C (+) CIRCUIT OPEN AT DLC

Fig 1: Measuring Resistance Of Diagnostic CAN C (+) Circuit Between TIPM Connector & DLC
Courtesy of CHRYSLER LLC
1. Disconnect the TIPM C3 harness connector.
2. Measure the resistance on the (D52) Diagnostic CAN C (+) circuit between the TIPM C3 harness connector and the DLC.
  Is the resistance above 10.0 ohms?
  
  Yes
  - Repair the (D52) Diagnostic CAN C (+) circuit for an open.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
  No
  - Go to Step 6.
CHECK FOR (D51) DIAGNOSTIC CAN C (-) CIRCUIT OPEN AT DLC

Fig 2: Measuring Resistance Of Diagnostic CAN C (-) Circuit Between TIPM Connector & DLC
Courtesy of CHRYSLER LLC
1. Measure the resistance on the (D51) Diagnostic CAN C (-) circuit between the TIPM C3 harness connector and the DLC.
  Is the resistance above 10.0 ohms?
  
  Yes
  - Repair the (D51) Diagnostic CAN C (-) circuit for an open.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
  No
  - Go to Step 7.
CHECK FOR DIAGNOSTIC CAN C CIRCUITS SHORTED TOGETHER

Fig 3: Measuring Resistance Between Diagnostic CAN C (+) Circuit & Diagnostic CAN C (-) Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between the (D52) Diagnostic CAN C (+) circuit and the (D51) Diagnostic CAN C (-) circuit at the TIPM C3 harness connector.
  Is the resistance below 100.0 ohms?
  
  Yes
  - Repair the (D52) Diagnostic CAN C (+) circuit for a short to the (D51) Diagnostic CAN C (-) circuit.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .
  No
  - Replace the Totally Integrated Power Module in accordance with the service information.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure .