Diagnostic Test

WARNING: This page is about a different car, the 2007 Chrysler PT Cruiser. However, it is still accessible from the selected car via links, so may be relevant.

1) CHECK FOR ACTIVE INTERNAL FAULTS, IGNITION FAULTS, AND BATTERY FAULTS IN THE OCCUPANT CLASSIFICATION MODULE (OCM)
NOTE: Ensure that the battery is fully charged.

Turn the ignition on, then off, and then on again.

With the scan tool, read Occupant Classification Module (OCM) DTCs.

Does the scan tool display any active DTCs relating to internal faults, ignition faults or battery faults?

Yes
1. Diagnose and repair the DTCs. Refer to the DIAGNOSTIC CODE INDEX for a complete list of symptoms.
No
1. Go to 2).
2) VERIFY THAT DTC B1B7D-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT PERFORMANCE IS ACTIVE
With the scan tool, read OCM DTCs.

Does the scan tool display active: B1B7D-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT PERFORMANCE?

Yes
1. Go to 3).
No
1. Go to 6).
3) INSPECT PASSENGER SEAT HARNESS WIRES AND CONNECTORS
WARNING: To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

Using the wiring diagram/schematic as a guide, inspect the Passenger Seat Harness wiring and connectors. Look for chafed, pierced, pinched or partially broken wires and broken, bent, pushed out, spread, corroded or contaminated terminals.

Are any of these conditions present?

Yes

NOTE: Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.
1. Replace the Passenger Seat Harness in accordance with the Service Information.
2. Perform *OCM SYSTEM VERIFICATION TEST .
3. Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1 .
No
1. Go to 4).
4) PERFORM OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST
NOTE: Failure to follow test instructions or aborting the test will cause faults to set when performing the Occupant Classification Module System Verification Test. To prevent faults due to process errors: Verify That All Tests Steps That Led You Here Were Performed As Directed; Verify That The Ignition Is In Run; Wait 30 Seconds After Changing The Seat Weight Before Proceeding To Allow The System To Stabilize; Only Press Scan Tool Buttons When Directed To Do So; and Perform The Occupant Classification Module System Verification Test To Completion.

With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is complete, wait two minutes, and then proceed as follows.

With the scan tool, read OCM DTCs.

Does the scan tool display any active PASSENGER SEAT WEIGHT SENSOR PERFORMANCE DTCs?

Yes
1. Go to 5).
No - But Other DTCs Present
1. Diagnose and repair the DTCs. Refer to the DIAGNOSTIC CODE INDEX for a complete list of symptoms.
No - No Active DTCs Present
1. Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1 .
5) PERFORM OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST
WARNING: To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

Verify that all of the Seat Weight Sensor mounting screws are torqued to specification. Refer to SEATS .

WARNING: To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.

NOTE: Failure to follow test instructions or aborting the test will cause faults to set when performing the Occupant Classification Module System Verification Test. To prevent faults due to process errors: Verify That All Tests Steps That Led You Here Were Performed As Directed; Verify That The Ignition Is In Run; Wait 30 Seconds After Changing The Seat Weight Before Proceeding To Allow The System To Stabilize; Only Press Scan Tool Buttons When Directed To Do So; and Perform The Occupant Classification Module System Verification Test To Completion.

With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is complete, wait two minutes, and then proceed as follows.

With the scan tool, read OCM DTCs.

Does the scan tool display any active PASSENGER SEAT WEIGHT SENSOR PERFORMANCE DTCs?

Yes
1. Perform the *DIAGNOSIS AND CHECKOUT PROCEDURE FOR SEAT WEIGHT SENSORS .
No - But Other DTCs Present
1. Diagnose and repair the DTCs. Refer to the DIAGNOSTIC CODE INDEX for a complete list of symptoms.
No - No Active DTCs Present
1. Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1 .
6) CHECKING STORED OR INTERMITTENT CODES
NOTE: Diagnose and repair all active codes before diagnosing stored codes. Refer to the DIAGNOSTIC CODE INDEX for a complete list of airbag system diagnostic procedures.

With the scan tool, record and erase all Airbag System Module DTCs.

WARNING: To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

Using the wiring diagram/schematic as a guide, inspect the related wiring and connectors for chafed, pierced, pinched, and partially broken wires, and for broken, bent, pushed out, corroded, and contaminated terminals. Repair as necessary.

Reconnect all disconnected components and harness connectors.

WARNING: To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.

With the scan tool, monitor for active codes while performing the following:
- Wiggle the wiring harness and connectors of the related airbag circuit.
- Continue the test until either a code becomes active or the problem area is isolated.
In the previous steps you have attempted to recreate the conditions responsible for setting the DTC in question/causing the intermittent condition.

Are any ACTIVE DTCs present?

Yes
1. Select the appropriate diagnostic procedure from the DIAGNOSTIC CODE INDEX .
No
1. No problem found at this time. Perform the *OCM SYSTEM VERIFICATION TEST . Erase all codes before returning vehicle to customer.