LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2006 >> PT Cruiser Base, 2D Convertible, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 43 (DTCS B1B21 To B1B82) >> B1B57-1ST Row Passenger Seat Belt Sensor Circuit Shorted Together >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2007 Chrysler PT Cruiser. However, it is still accessible from the selected car via links, so may be relevant.
  1. 1) VERIFY THAT DTC B1B57-1ST ROW PASSENGER SEAT BELT SENSOR CIRCUIT SHORTED TOGETHER IS ACTIVE 
    NOTE: Ensure the battery is fully charged.

    Turn the ignition on.

    With the scan tool, read ORC DTCs.

    Does the scan tool display active DTC: B1B57-1ST ROW PASSENGER SEAT BELT SENSOR CIRCUIT SHORTED TOGETHER? 

    Yes 

    1. Go to  2).

    No 

    1. Go to  6).
  2. 2) CHECK FOR HIGH VOLTAGE ON THE PASSENGER HALL EFFECT CIRCUITS 
    Fig 1: Checking For High Voltage On Passenger Hall Effect Circuits
    GC0058388Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Disconnect the Passenger Seat Belt Switch connector.

    NOTE: Check connectors - Clean and repair as necessary.

    Turn the ignition on.

    Measure the voltage between the (R274) Passenger Hall Effect (+) circuit cavity 1 in the Passenger Seat Belt Connector and ground.

    Measure the voltage between the (R272) Passenger Hall Effect (-) circuit between cavity 2 in the Passenger Seat Belt Connector and ground.

    Is the voltage above 5 volts on either circuit? 

    Yes 

    1. Go to  5).

    No 

    1. Go to  3).
  3. 3) CHECK FOR A ORC PASSENGER HALL EFFECT CIRCUITS SHORTED TOGETHER 
    Fig 2: Checking For ORC Passenger Hall Effect Circuits Shorted Together
    GC0058392Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Measure the resistance between the (R272) Passenger Hall Effect (-) circuit cavity 1 and (R274) Passenger Hall Effect (+) circuit cavity 2 in the Passenger Seat Belt Switch connector.

    Is the resistance below 10.0 Ohms? 

    Yes 

    1. Go to  4).

    No 

    1. Replace the shorted Passenger Seat Belt Switch in accordance with the service information.
    2. Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1 .
  4. 4) CHECK FOR PASSENGER HALL EFFECT CIRCUITS SHORTED TOGETHER 
    Fig 3: Checking For Shorted Passenger Hall Effect Circuits
    GC0058392Courtesy of CHRYSLER LLC
    WARNING: To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

    Disconnect the both ORC connectors.

    NOTE: Check connectors - Clean and repair as necessary.

    Connect the 8443-24 Load Tool Adapter to the ORC C1 connector.

    Measure the resistance between the (R274) Passenger Hall Effect (+) circuit and (R272) Passenger Hall Effect (-) circuit in the Passenger Seat Belt Connector.

    Is the resistance below 5.0 Ohms? 

    Yes 

    1. Repair the open Passenger Hall Effect (-) circuit.
    2. Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1 .

    No 

      WARNING: If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment and serious or fatal injury.
    1. Replace the ORC in accordance with the service information.
    2. Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1 .
  5. 5) CHECK FOR A PASSENGER HALL EFFECT CIRCUITS SHORTED HIGH 
    Fig 4: Checking For Passenger Hall Effect Circuits Voltage Shorted High
    GC0058388Courtesy of CHRYSLER LLC
    WARNING: To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

    Disconnect the both ORC connectors.

    NOTE: Check connectors - Clean and repair as necessary.

    Connect the 8443-24 ORC Adapter to the ORC C1 connector.

    Measure the voltage of the (R274) Passenger Hall Effect (+) circuit from cavity 1 of the Passenger Seat Belt Connector to ground.

    Measure the voltage of the (R272) Passenger Hall Effect (-) circuit from cavity 2 of the Passenger Seat Belt Connector to ground.

    Is there any voltage on either circuit? 

    Repair  

    1. Repair the shorted to battery (R274) Passenger Hall Effect (+) circuit or (R272) Passenger Hall Effect (-) circuit in accordance with the service information.
    2. Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1 .

    No 

      WARNING: If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment and serious or fatal injury.
    1. Replace the ORC in accordance with the service information.
    2. Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1 .
  6. 6) TEST FOR INTERMITTENT CONDITION 

    With the scan tool, record and erase all DTCs from all Airbag modules.

    If any ACTIVE codes are present they must be resolved before diagnosing any stored codes.

    WARNING: To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

    Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.

    Look for chafed, pierced, pinched or partially broken wires and broken, bent, pushed out, spread, corroded or contaminated terminals.

    The following additional checks may assist you in identifying a possible intermittent problem.

    Reconnect any disconnected components and harness connector.

    WARNING: To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.

    With the scan tool, monitor active codes as you work through the following steps.

    WARNING: To avoid serious or fatal injury, maintain a safe distance from all airbags while performing the following steps.

    Wiggle the wiring harness and connectors of the related airbag circuit or component.

    If only stored codes return, continue the test until the problem area has been isolated.

    In the previous steps you have attempted to recreate the conditions responsible for setting the active DTC in question.

    Does the scan tool display any ACTIVE DTCs? 

    Yes 

    1. Select the appropriate diagnostic procedure from the DIAGNOSTIC CODE INDEX .

    No 

    1. No problem found at this time. Erase all codes before returning vehicle to customer.
scientia non olet · About LEMON Manuals