LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2006 >> PT Cruiser Base, 2D Convertible, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 34 (G288 Manual Transmission - Overhaul) >> G288 Manual Transaxle >> Assembly >> G288 Manual Transaxle

G288 Manual Transaxle

WARNING: This page is about a different car, the 2007 Chrysler PT Cruiser. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Input Shaft Oil Trough
GC0022044Courtesy of CHRYSLER LLC
1 - OIL TROUGH
  1. Install input shaft oil trough (1) to transaxle housing. See Fig 1.
    Fig 2: Output Shaft Oil Trough
    GC0022045Courtesy of CHRYSLER LLC
    1 - OIL TROUGH
  2. Install output shaft oil trough (1) to transaxle housing. See Fig 2.
    Fig 3: Removing/Installing Output Shaft Bearing
    GC0022065Courtesy of CHRYSLER LLC
    1 - INPUT SHAFT BEARING
    2 - OUTPUT SHAFT BEARING
  3. Install output shaft roller bearing to clutch bellhousing (1, 2). See Fig 3.
    Fig 4: Differential Assembly
    GC0022050Courtesy of CHRYSLER LLC
    1 - DIFFERENTIAL ASSEMBLY
  4. Install differential assembly (1). See Fig 4.
    Fig 5: Heating Reverse Shaft Bearing Bore
    GC0022051Courtesy of CHRYSLER LLC
    1 - HEAT GUN
    2 - BEARING BORE
  5. Using heat gun (1), heat reverse shaft bearing bore (2) in transaxle case to expand for reverse shaft/bearing installation. See Fig 5.
    Fig 6: Reverse Shaft & Fork Assembly
    GC0022052Courtesy of CHRYSLER LLC
    1 - FORK/ROD ASSY.
    2 - REVERSE SHAFT ASSY.
  6. Install reverse shaft (2) and fork/rod (1). See Fig 6.
    Fig 7: Installing Geartrain to Clutch Bellhousing
    GC0022053Courtesy of CHRYSLER LLC
    1 - GEARTRAIN
    2 - REVERSE SHAFT ASSY.
  7. Install geartrain (1) (with forks/rods) into case. See Fig 7.
    Fig 8: View Of Properly Installed Geartrain
    GC0022054Courtesy of CHRYSLER LLC
    1 - INTERMEDIATE SHAFT
    2 - INPUT SHAFT
  8. Verify proper installation of input (2) and output shaft (1) assemblies, as well as proper orientation of shift rod/fork assemblies. See Fig 8.
    Fig 9: Installing Geartrain Housing
    GC0022055Courtesy of CHRYSLER LLC
    1 - TRANSAXLE HOUSING
    2 - CLUTCH BELLHOUSING
    3 - SEALER BEAD
  9. Install chip collector magnet to case and retain with grease.
  10. Apply a bead (3) of Mopar® Gasket Maker or Omnifit FD-40 to clutch bellhousing flange (2). Install geartrain housing (1). See Fig 9.
    Fig 10: Geartrain Housing-To-Clutch Bellhousing Bolts (Short)
    GC0022040Courtesy of CHRYSLER LLC
    1 - BOLTS (18-SHORT)
  11. Install transaxle housing-to-clutch bellhousing short bolts (1) by hand. See Fig 10.
    Fig 11: Geartrain Housing-To-Clutch Bellhousing Bolts (Long)
    GC0022041Courtesy of CHRYSLER LLC
    1 - BOLTS (2-LONG)
  12. Install transaxle housing-to-clutch bellhousing long bolts (1) by hand. See Fig 11.
    Fig 12: Torquing Transaxle Housing-To-Clutch Bellhousing Bolts
    GC0022056Courtesy of CHRYSLER LLC
    1 - TORQUE WRENCH
  13. Torque (1) twenty (18 short, 2 long) geartrain housing-to-clutch bellhousing bolts to 28 N.m (21 ft. lbs.) torque. See Fig 12.
    Fig 13: Installing Input Shaft Roller Bearing
    GC0022057Courtesy of CHRYSLER LLC
    1 - HANDLE C-4171
    2 - INSTALLER 8871
    3 - SNAP RING
    4 - BEARING
  14. Using an arbor press and Handle C-4171 (1) and Installer 8871(2), install input shaft roller bearing (4). See Fig 13.
    Fig 14: Installing Output Shaft Bearing
    GC0022058Courtesy of CHRYSLER LLC
    1 - HANDLE C-4171
    2 - INSTALLER 8871
    3 - BEARING
  15. Using an arbor press and Handle C-4171 (1) and Installer 8871(2), install output shaft roller bearing (3). See Fig 14.
    Fig 15: Engaging Fifth Gear
    GC0022037Courtesy of CHRYSLER LLC
    1 - FIFTH GEAR FORK
    2 - SCREWDRIVER
  16. Engage fifth gear (1). See Fig 15.
    Fig 16: Engaging Reverse Gear
    GC0022038Courtesy of CHRYSLER LLC
    1 - REVERSE GEAR FORK
    2 - SCREWDRIVER
  17. Engage reverse gear (1). See Fig 16.
    Fig 17: Bearing Retaining Screws
    GC0022039Courtesy of CHRYSLER LLC
    1 - RETAINING SCREWS (2)
  18. Install new  bearing retaining screws (1) and torque to 90-100 N.m (66-74 ft. lbs.). See Fig 17.
    Fig 18: Input Shaft Oil Diverter
    GC0022035Courtesy of CHRYSLER LLC
    1 - DIVERTER
    2 - LOCATING PROVISIONS
  19. Install input shaft oil diverter (1). See Fig 18.
    Fig 19: Output Shaft Oil Diverter
    GC0022036Courtesy of CHRYSLER LLC
    1 - DIVERTER
    2 - LOCATOR PROVISIONS
  20. Install output shaft oil diverter (1). See Fig 19.
    Fig 20: Proper Sealer Application
    GC0022059Courtesy of CHRYSLER LLC
    1 - OIL DIVERTERS
    2 - SEALER BEAD
  21. Install a bead (2) of Mopar® Gear Sealant RTV to geartrain housing. See Fig 20.
    Fig 21: Sealer To Cover Application Locations
    GC0022060Courtesy of CHRYSLER LLC
    1 - SEALER BEAD
    2 - END COVER
  22. Install a bead (1) of Mopar® Gear Sealant RTV to end cover. See Fig 21.
    Fig 22: End Cover-To-Case Bolts
    GC0022033Courtesy of CHRYSLER LLC
    1 - END COVER
    2 - BOLT (9)
  23. Immediately install end cover (1) to geartrain housing. Install and torque nine (9) bolts (2) to 20-25 N.m (15-18 ft. lbs.). See Fig 22.
    Fig 23: Identifying Sealer To Shift Shaft Mounting Application Locations
    GC0022061Courtesy of CHRYSLER LLC
    1 - SEALER BEAD
  24. Install bead (1) of Mopar® Gasket Maker or Omnifit FD-1664 to shift shaft assembly mounting pad. See Fig 23.
    Fig 24: Shift Shaft-To-Case Bolts
    GC0022031Courtesy of CHRYSLER LLC
    1 - BOLT (4)
    NOTE: When installing shift shaft assembly, do not handle assembly by counterweight.
  25. Install shift shaft assembly. Use caution when installing. It is necessary to guide slot in shaft assembly over locating pin which is pressed into case.
  26. Install crossover lever assembly and four bolts (1). See Fig 24. Torque Shift Mechanism-to-Case bolts to 20-25 N.m (15-18 ft. lbs.).
    Fig 25: Identifying Plug, Spring & Pin
    GC0022029Courtesy of CHRYSLER LLC
    1 - PLUG
    2 - SPRING
    3 - PIN
  27. Install shift shaft crossover detent pin (1), spring (2) and plug (3). See Fig 25. Torque plug to 20 N.m (15 ft. lbs.).
    Fig 26: Shift Shaft Detent Assembly
    GC0022030Courtesy of CHRYSLER LLC
    1 - DETENT ASSEMBLY
  28. Install shift shaft selector detent assembly (1) with Mopar® Lock 'n Seal™. See Fig 26. Torque detent assembly 20-25 N.m (15-18 ft. lbs.).
    Fig 27: Backup Lamp Switch
    GC0022047Courtesy of CHRYSLER LLC
    1 - BACKUP LAMP SWITCH
  29. Install back-up lamp switch (1). See Fig 27. Torque switch to 24 N.m (18 ft. lbs.).
    Fig 28: Seat with Soft-Tipped Hammer
    GC0022062Courtesy of CHRYSLER LLC
    1 - DETENT PLUGS
    2 - SOFT-TIPPED HAMMER
  30. Install four shift rod detent plugs (1). Install new plugs as necessary.  Tap into place using a soft-tipped hammer (2). See Fig 28.
    Fig 29: Installing Input Shaft Seal
    GC0022064Courtesy of CHRYSLER LLC
    1 - INSTALLER 8864
    2 - SEAL, INPUT SHAFT
  31. Install input shaft seal (2) using Installer 8864 (1). See Fig 29.
    Fig 30: Installing Axle Seal
    GC0022063Courtesy of CHRYSLER LLC
    1 - INSTALLER 8916
  32. Install output (axle) shaft seals using Installer 8916 (1). See Fig 30.
    Fig 31: Removing/Installing Concentric Slave Cylinder
    GC0022048Courtesy of CHRYSLER LLC
    1 - CONCENTRIC SLAVE CYLINDER
  33. Install concentric slave cylinder (1). See Fig 31. Torque bolts in three passes to specified torque. See TORQUE SPECIFICATIONS .
scientia non olet · About LEMON Manuals