LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2006 >> PT Cruiser Base, 2D Convertible, Standard >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> 2.4L Engine - DTCS P0016 To P0125, Diagnostic Code Index, Pre-Diagnostic Troubleshooting Procedure & Intermittent Condition >> Diagnosis And Testing >> P0016-Crankshaft / Camshaft Timing Misalignment >> Diagnostic Test

Diagnostic Test

  1. 1)  ACTIVE DTC  
    WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in personal injury or death.

    With the scan tool clear the DTC(s).

    Start the engine and run until operating temp is reached. (Closed Loop)

    If the DTC does not reset it may be necessary to test drive the vehicle.

    Does the P0016 return? 

    Yes 

    1. Go To  2).

    No 

    1. Refer to the INTERMITTENT CONDITION  Diagnostic Procedure.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .
  2. 2)  CHECKING THE CMP SIGNAL WITH A LAB SCOPE 
    Fig 1: CHECKING THE CMP SIGNAL
    GC0041517Courtesy of DAIMLERCHRYSLER CORP.

    With a lab scope, backprobe the (K44) CMP Signal circuit at the CMP Sensor harness connector.

    WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in personal injury or death.

    Start the engine.

    Observe the lab scope screen.

    Are there any irregular or missing signals? 

    Yes 

    1. Go To  3).

    No 

    1. Go To  6).
  3. 3)  CMP WIRE HARNESS INSPECTION 

    Turn the ignition off.

    Visually inspect the related wire harness. Look for any chafed, pierced, pinched, or partially broken wires.

    Visually inspect the related wire harness connectors. Look for broken, bent, pushed out, or corroded terminals.

    Make sure the Crankshaft Position Sensor and the Camshaft Position Sensor are properly installed and the mounting bolt(s) are torqued to their proper specification.

    Refer to any TSBs that may apply.

    Were any of the above conditions present? 

    Yes 

    1. Refer to the INTERMITTENT CONDITION  Diagnostic Procedure.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .

    No 

    1. Go To  4).
  4. 4)  TONE WHEEL/PULSE RING INSPECTION 

    Remove the Camshaft Position Sensor.

    Inspect the Tone Wheel/Pulse Ring for damage, foreign material, or excessive movement.

    Were any problems found? 

    Yes 

    1. Refer to the INTERMITTENT CONDITION  Diagnostic Procedure.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .

    No 

    1. Go To  5).
  5. 5)  CAMSHAFT POSITION SENSOR  

    If there are no possible causes remaining, view repair. 

    Repair 

    1. Replace the Camshaft Position Sensor.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .
  6. 6)  ERRATIC CMP SIGNAL  

    Turn the ignition off.

    Remove the lab scope probe.

    WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in personal injury or death.

    Ignition on, engine not running.

    With scan tool, erase DTCs.

    Start the engine.

    Gently tap on and wiggle the Cam Position Sensor.

    Ignition on, engine not running.

    Inspect the Sensor connector and harness connector, and inspect the PCM connector and harness connector for loose, bent, corroded, or pushed out pins/terminals.

    Inspect the related wire harness and the splices in the CMP circuit.

    Does the P0016 return? 

    Yes 

    1. Repair the wiring/connector concerns as needed or replace the Camshaft Position Sensor.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .

    No 

    1. Go To  7).
  7. 7)  CHECKING THE CKP SIGNAL WITH A LAB SCOPE 
    Fig 2: CHECKING THE CKP SIGNAL
    GC0041518Courtesy of DAIMLERCHRYSLER CORP.

    Turn the ignition off.

    With a lab scope, backprobe the (K24) CKP Signal circuit at the CKP harness connector.

    WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in personal injury or death.

    Start the engine.

    Observe the lab scope screen.

    Are there any irregular or missing signals? 

    Yes 

    1. Go To  8).

    No 

    1. Go To  10).
  8. 8)  CKP WIRE HARNESS INSPECTION 

    Turn the ignition off.

    Visually inspect the related wire harness. Look for any chafed, pierced, pinched, or partially broken wires.

    Visually inspect the related wire harness connectors. Look for broken, bent, pushed out, or corroded terminals.

    Make sure the Crankshaft Position Sensor and the Camshaft Position Sensor are properly installed and the mounting bolt(s) are torqued to their proper specification.

    Refer to any TSBs that may apply.

    Were any of the above conditions present? 

    Yes 

    1. Repair as necessary.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .

    No 

    1. Go To  9).
  9. 9)  TONE WHEEL/FLEX PLATE INSPECTION 

    Remove the Crankshaft Position Sensor.

    Inspect the Tone Wheel/Flex Plate slots for damage, foreign material, or excessive movement.

    Were any problems found? 

    Yes 

    1. Repair or replace the Tone Wheel/Flex Plate as necessary.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .

    No 

    1. Replace the Crankshaft Position Sensor.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .
  10. 10)  ERRATIC CKP SIGNAL  
    NOTE: The conditions that set this DTC are not present at this time. The following test may help in identifying the intermittent condition.
    WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in personal injury or death.

    Start the engine.

    Gently tap on and wiggle the Crank Position Sensor.

    Turn the ignition off.

    Inspect the Sensor connector and harness connector, and inspect the PCM connector and harness connector for loose, bent, corroded, or pushed out pins/terminals.

    Inspect the related wire harness and the splices in the CKP circuits.

    Were any problems found? 

    Yes 

    1. Repair the wiring/connector concerns as needed or replace the Crankshaft Position Sensor.
    2. Perform the POWERTRAIN VERIFICATION TEST. (Refer to ENGINE - STANDARD PROCEDURE - POWERTRAIN VERIFICATION TEST) .

    No 

    1. Test Complete.
scientia non olet · About LEMON Manuals