LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2005 >> Pacifica Limited >> Repair and Diagnosis >> Accessories & Equipment >> Seats >> Body Diagnostic Procedures - Diagnostic Information And Procedures - Chime, Communication, Door Ajar, Electrically Heated Systems, Exterior Lighting >> Electrically Heated Systems >> Symptom: DRIVER SEAT HEAT OUTPUT SHORT TO GROUND - MHSAPM >> Diagnostic Procedure

Diagnostic Procedure

DRIVER SEAT HEAT OUTPUT SHORT TO GROUND SYMPTOM CHART

TEST ACTION APPLICABILITY
1 With the DRBIII®, erase the DTC from Memory/Heated Seat Adjustable Pedal Module.
Turn the ignition switch to the Off position then start the engine and let run for one minute.
Operate the heated seat system.
With the DRBIII® check for the same DTC to reset in the MHSAPM.
Did the same DTC reset?
Yes --> Go To 2
No --> Using the wiring diagram/schematic as a guide, inspect the wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1 .		 All
2 Disconnect the Driver Heated Seat Cushion 4-way connector.
With the DRBIII®, erase DTC's.
Turn the Driver Seat Heater on.
Using the DRBIII re-read DTC's
Does the DRBIII® show the same code?
Yes --> Go To 3
No --> Go To 5		 All
3 Turn ignition off.
Disconnect the Driver Heated Seat Cushion 4-way connector.
Disconnect the MHSAPM C3 connector.
Measure the resistance of the Driver Seat Heater B(+) Driver circuit to the Driver Seat Heater Ground circuit.
Is the resistance below 1000.0 ohms?
Yes --> Repair the Driver Seat Heater B(+) Driver wire for a short to the Driver Seat Heater Ground circuit.
Perform BODY VERIFICATION TEST - VER 1 .
No --> Go To 4		 All
4 Turn ignition off.
Disconnect the Driver Heated Seat Cushion 4-way connector.
Disconnect the MHSAPM C3 connector.
Measure the resistance of the Driver Seat Heater B(+) Driver circuit to ground.
Is the resistance below 1000.0 ohms?
Yes --> Repair the Driver Seat Heater B(+) Driver wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1 .
No --> Replace the Memory Heated Seat Adjustable Pedal Module
Perform BODY VERIFICATION TEST - VER 1 .		 All
5 Disconnect the Driver Heated Seat Cushion 4-way connector.
Measure the resistance of the Driver Seat Heater B(+) Driver circuit in the Driver Heated Seat Cushion 4-way connector cushion side to body ground.
Is the resistance below 1000.0 ohms?
Yes --> Repair the pigtail wiring for a short to the seat frame or replace the Driver Heated Seat Cushion/Element as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
No --> Go To 6		 All
6 Disconnect the Driver Heated Seat Back 2-way connector.
Measure the resistance of the Driver Heated Seat Driver to the Driver Seat Heater Ground, in the Driver Heated Seat Back 2-way connector seat back side.
Is the resistance below 4.0 ohms?
Yes --> Replace the Driver Heated Seat Back/Element as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
No --> Go To 7		 All
7 Disconnect the Driver Heated Seat Back 2-way connector if disconnected.
Disconnect the Driver Heated Seat Cushion 4-way connector.
Measure the resistance of the Driver Seat Heater B(+) Driver circuit to the Driver Seat Heater Ground circuit at the Driver Heated Seat Cushion 4-way connector.
Is the resistance below 3.5 ohms?
Yes --> Repair the Driver Seat Heater B(+) Driver circuit for a short to the Driver Seat Heater Ground circuit or replace the Driver Heated Seat Cushion/Element as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
No --> Inspect the heated seat wiring for a short that may have been removed during testing and repair as necessary.
Perform BODY VERIFICATION TEST - VER 1 .		 All
scientia non olet · About LEMON Manuals