LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2005 >> Pacifica Limited >> Repair and Diagnosis >> Accessories & Equipment >> Seats >> Body Diagnostic Procedures - Diagnostic Information And Procedures - Chime, Communication, Door Ajar, Electrically Heated Systems, Exterior Lighting >> Communication >> Symptom: *NO RESPONSE FROM OCCUPANT RESTRAINT CONTROLLER >> Diagnostic Procedure

Diagnostic Procedure

NO RESPONSE FROM OCCUPANT RESTRAINT CONTROLLER SYMPTOM CHART

TEST ACTION APPLICABILITY
1
NOTE: Check the IPM for DTC's. If DTC's are present, go to the appropriate test.
Ensure that the battery is fully charged.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Occupant Restraint Controller harness connector.Connect the appropriate Load Tool ACM Adapter to the ORC connectorTurn the ignition on and then reconnect the Battery.Using a 12-volt test light connected to ground, probe the ORC Run Driver Circuit and the ORC Run/Start Driver Circuit at the Occupant Restraint Controller connector.
NOTE: One open circuit will not cause a NO RESPONSE condition.
Is the test light illuminated on both circuits?Yes --> Go To 2No --> Repair the ORC Run Driver and the ORC Run/Start Driver circuits for an open.Perform AIRBAG VERIFICATION TEST - VER 1 .
NOTE: When reconnecting airbag system components, the ignition must be turned, off and the battery must be disconnected.
 All
2 Ensure that the battery is fully charged.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.

Disconnect the Occupant Restraint Controller harness connector.
Connect the appropriate Load Tool ACM Adapter to the ORC connector.
Using a 12-volt test light connected to 12-volts, probe the ground circuit.
NOTE: Make sure test light is connected to the Battery positive terminal.

Is the test light illuminated?
Yes --> Go To 3
No --> Repair the Ground circuit for an open.
Perform AIRBAG VERIFICATION TEST - VER 1 .
When reconnecting Airbag system components, the ignition must be turned off and the battery must be disconnected. 		 All
3
NOTE: Ensure there is PCI bus communication with other modules. If not, refer to the PCI BUS COMMUNICATION FAILURE  symptom and repair as necessary.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Occupant Restraint Controller harness connector.Connect the appropriate Load Tool ACM Adapter to the ORC connector.Turn the ignition on and then reconnect the Battery.Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and black test probes.Connect the scope input cable to the channel one connector on the DRB. Attach the red and black leads and the cable to probe adapter to the scope input cable.With the DRBIII® select Pep Module Tools.Select lab scope.Select Live Data.Select 12 volt square wave.Press F2 for Scope.Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again when complete.Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus circuit in the ORC connector.Observe the voltage display on the DRB Lab Scope.Does the voltage pulse from 0 to approximately 7.5 volts?Yes --> Go To 4.No --> Repair the PCI Bus circuit for an open.Perform AIRBAG VERIFICATION TEST - VER 1 .		 All
4 If there are no possible causes remaining, view repair.
Repair
Replace the Occupant Restraint Controller in accordance with the Service information.
Perform AIRBAG VERIFICATION TEST - VER 1 .		 All
scientia non olet · About LEMON Manuals