LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2004 >> Sebring Limited, 2D Convertible >> Repair and Diagnosis >> Accessories & Equipment >> Anti-Theft Systems >> Powertrain Diagnostic Procedures - NGC DRIVEABILITY Symptoms, NGC DRIVEABILITY Diagnostic Tests DTCS P0016 To P0461 - Except Coupe >> DRIVEABILITY - NGC - Diagnostic Tests >> DTC P0461: Fuel Level Sensor #1 Performance >> Possible Causes

Possible Causes

GOOD TRIP EQUAL TO ZERO

VISUALLY INSPECT FUEL TANK

(G4) FUEL LEVEL SIGNAL CIRCUIT SHORTED TO GROUND

(G4) FUEL LEVEL SIGNAL CIRCUIT OPEN

(Z2) GROUND CIRCUIT OPEN

INTERNAL INSPECTION OF THE FUEL TANK

FUEL LEVEL SENSOR

DIAGNOSTIC PROCEDURE - P0461-FUEL LEVEL SENSOR #1 PERFORMANCE

TEST ACTION
1
NOTE: Diagnose P0462 or P0463 first, if set along with P0461.
NOTE: Inspect the Fuel Pump Module harness connector for any corrosion or damage.
Ignition on, engine not running.With the DRBIII®, read DTCs and record the related Freeze Frame data.Is the Good Trip Counter displayed and equal to zero?
  1. Yes --> Go To 2
  2. No --> Refer to the INTERMITTENT CONDITION  symptom in the Driveability category.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
2 Visually inspect the Fuel Tank for damage that may restrict the Fuel Sending Unit float from moving.
Is the Fuel Tank OK?
  1. Yes --> Go To 3
  2. No --> Replace the Fuel Tank as necessary.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
3 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Measure the resistance between ground and the (G4) Fuel Level Signal circuit at the Fuel Pump Module harness connector.
Is the resistance below 100 ohms?
  1. Yes --> Repair the short to ground in the (G4) Fuel Level Signal circuit.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .

  2. No --> Go To 4
4 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Disconnect the Instrument Cluster harness connector.
Measure the resistance of the (G4) Fuel Level Signal circuit from the Fuel Pump Module harness connector to the BCM harness connector.
Is the resistance below 5.0 ohms?
  1. Yes --> Go To 5
  2. No --> Repair the open in the (G4) Fuel Level Signal circuit.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
5 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Measure the resistance of the (Z2) Ground circuit from the Fuel Pump Module harness connector to ground.
Is the resistance below 5.0 ohms?
  1. Yes --> Go To 6
  2. No --> Repair the open in the (Z2) Ground circuit.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
6
WARNING: The fuel system is under a constant pressure even with the engine off. Before opening the fuel system the fuel pressure must be release. Relieve the fuel pressure in accordance with the service information.
Remove the Fuel Tank in accordance with the Service Information.Remove the Fuel Pump Module.Visually inspect the inside of the Fuel Tank for any obstructions or deformities.Inspect the Fuel Pump Module Float arm for damage.Were any problems found?
  1. Yes --> Repair or replace as necessary.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .

  2. No --> Go To 7
7 If there are no possible causes remaining, view repair.
Repair:
Replace the Fuel Level Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
scientia non olet · About LEMON Manuals