LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2004 >> Sebring LXi, 2D Convertible >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> Powertrain Diagnostic Procedures - NGC DRIVEABILITY Symptoms, NGC DRIVEABILITY Diagnostic Tests DTCS P0016 To P0461 - Except Coupe >> DRIVEABILITY - NGC - Diagnostic Tests >> DTC P0073: Ambient Temp Sensor High >> Possible Causes

Possible Causes

AMBIENT AIR TEMPERATURE SENSOR VOLTAGE ABOVE 4.8 VOLTS

(K25) AAT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE

AMBIENT AIR TEMPERATURE SENSOR INTERNAL FAILURE

(K25) AAT SIGNAL CIRCUIT OPEN

(K4) SENSOR GROUND CIRCUIT OPEN

PCM

DIAGNOSTIC PROCEDURE - P0073-AMBIENT TEMP SENSOR HIGH

TEST ACTION
1 Ignition on, engine not running.
With the DRBIII®, read the Ambient Air Temperature Sensor voltage.
Is the voltage above 4.8 volts?
  1. Yes --> Go To 2
  2. No --> Refer to the INTERMITTENT CONDITION  symptom in the Driveability category.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
2 Turn the ignition off.
Disconnect the Ambient Air Temperature Sensor harness connector.
Ignition on, engine not running.
Measure the voltage of the (K25) AAT Signal circuit in the Ambient Air Temperature Sensor harness connector.
Is the voltage above 5.2 volts?
  1. Yes --> Repair the short to battery voltage in the (K25) AAT Signal circuit.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .

  2. No --> Go To 3
3 Turn the ignition off.
Disconnect the Ambient Air Temperature Sensor harness connector.
Connect a jumper wire between the (K145) AAT Signal circuit and the (K167) Sensor ground circuit in the Ambient Air Temperature Sensor harness connector.
Ignition on, engine not running.
With the DRBIII®, read Ambient Air Temperature Sensor voltage.
Is the voltage below 1.0 volt?
  1. Yes --> Replace the Ambient Air Temperature Sensor.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .

  2. No --> Go To 4
4 Turn the ignition off.
Disconnect the Ambient Air Temperature Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMINALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.

Measure the resistance of the (K25) AAT Signal circuit from the Ambient Air Temperature Sensor harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
  1. Yes --> Go To 5
  2. No --> Repair the open in the (K25) AAT Signal circuit.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
5 Turn the ignition off.
Disconnect the Ambient Air Temperature Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMINALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.

Measure the resistance of the (K4) Sensor ground circuit from the Ambient Air Temperature Sensor harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
  1. Yes --> Go To 6
  2. No --> Repair the open in the (K4) Sensor ground circuit.

    Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
6
NOTE: Before continuing, check the PCM harness connector terminals for corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.Repair:Replace and program the Powertrain Control Module in accordance with the Service Information.Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC .
scientia non olet · About LEMON Manuals