Service Specifications
WARNING: This page is about a different car, the 2005 Dodge Stratus and 2005 Chrysler Sebring. However, it is still accessible from the selected car via links, so may be relevant.
SERVICE SPECIFICATIONS
| ITEM | STANDARD VALUE | LIMIT | |
|---|---|---|---|
| Timing belt | |||
| Auto-tensioner rod length mm (in) | 3.8 - 5.0 (0.15 - 0.20) |
- | |
| Auto-tensioner rod production length mm (in) | 12 (0.5) | - | |
| Auto-tensioner rod pushed-in amount [when pushed with a force of 98 - 196 N (22 - 44 lbs)] mm (in) | 1.0 (0.03) or less | - | |
| Rocker arms and camshaft | |||
| Camshaft cam height mm (in) | Intake | 37.71 (1.485) | Minimum 37.21 (1.465) |
| Exhaust | 37.14 (1.462) | Minimum 36.64 (1.443) | |
| Camshaft journal outside diameter mm (in) | 45 (1.8) | - | |
| Cylinder head and valves | |||
| Cylinder head flatness of gasket surface mm (in) | Less than 0.03 (0.001) | 0.2 (0.007) | |
| Cylinder head grinding limit of gasket surface mm (in) Total resurfacing depth of cylinder head and cylinder block | - | 0.2 (0.007) | |
| Cylinder head overall height mm (in) | 120 (4.7) | - | |
| Valve thickness of valve head (margin) mm (in) | Intake | 1.0 (0.04) | Minimum 0.5 (0.02) |
| Exhaust | 1.2 (0.05) | Minimum 0.7 (0.03) | |
| Valve overall height mm (in) | Intake | 112.30 (4.421) | Minimum 111.80 (4.402) |
| Exhaust | 114.11 (4.493) | Minimum 113.61 (4.473) | |
| Valve stem outside diameter mm (in) | Intake | 6.0 (0.24) | - |
| Exhaust | 6.0 (0.24) | - | |
| Valve thickness to valve guide clearance mm (in) | Intake | 0.02 - 0.05 (0.0008 - 0.0019) | 0.10 (0.003) |
| Exhaust | 0.04 - 0.07 (0.0016 - 0.0027) | 0.15 (0.005) | |
| Valve face angle mm (in) | 45° - 45.5° | - | |
| Valve spring free length mm (in) | 51.0 (2.01) | Minimum 50.0 (1.97) | |
| Valve spring load/installed height N (lb) /mm (in) | 267/44.2 (60.0/1.74) | - | |
| Valve spring out-of-squareness | 2° or less | 4° | |
| Valve seat valve contact width mm (in) | 0.9 - 1.3 (0.04 - 0.05) | - | |
| Valve guide inside diameter mm (in) | 6.0 (0.32) | - | |
| Valve guide projection from cylinder head upper surface mm (in) | 14.0 (0.55) | - | |
| Valve stem projection mm (in) | 49.30 (1.941) | 49.80 (1.960) | |
| Oversize rework dimensions of valve guide hole mm (in) | 0.05 oversize diameter | 11.05 - 11.07 (0.4351 - 0.4358) |
- |
| 0.25 oversize diameter | 11.25 - 11.27 (0.4429 - 0.4437) |
- | |
| 0.50 oversize diameter | 11.50 - 11.52 (0.4528 - 0.4535) |
- | |
| Intake oversize rework dimensions of valve seat hole mm (in) | 0.3 oversize diameter | 34.30 - 34.33 (1.3504 - 1.3515) |
- |
| 0.6 oversize diameter | 34.60 - 34.63 (1.3623 - 1.3633) |
- | |
| Exhaust oversize rework dimensions of valve seat hole mm (in) | 0.3 oversize diameter | 31.80 - 31.81 (1.2520 - 1.2531) |
- |
| 0.6 oversize diameter | 32.10 - 32.13 (1.2638 - 1.2650) |
- | |
| Oil pan and oil pump | |||
| Oil pump tip clearance mm (in) | 0.06 - 0.18 (0.003 - 0.007) | - | |
| Oil pump side clearance mm (in) | 0.04 - 0.10 (0.002 - 0.003) | - | |
| Oil pump body clearance mm (in) | 0.10 - 0.18 (0.004 - 0.007) | 0.35 (0.013) | |
| Oil pressure at curb idle speed kPa (psi) [oil temperature is 75 to 90°C (167 to 194°F)] | 80 (11.6) or more | - | |
| Piston and connecting rod | |||
| Piston outside diameter mm (in) | 91.1 (3.58) | - | |
| Piston ring to ring groove clearance mm (in) | No.1 | 0.03 - 0.07 (0.0012 - 0.0027) | 0.1 (0.003) |
| No.2 | 0.02 - 0.06 (0.0008 - 0.0023) | 0.1 (0.003) | |
| Piston ring end gap mm (in) | No.1 | 0.30 - 0.45 (0.012 - 0.017) | 0.8 (0.03) |
| No.2 | 0.45 - 0.60 (0.018 - 0.023) | 0.8 (0.03) | |
| Oil ring side rail | 0.20 - 0.60 (0.008 - 0.023) | 1.0 (0.03) | |
| Piston pin outside diameter mm (in) | 22.0 (0.87) | - | |
| Piston pin press-in load N (lbs) (room temperature) | 7,350 - 17,200 (1,653 - 3,866) |
- | |
| Crankshaft pin oil clearance mm (in) | 0.02 - 0.05 (0.0008 - 0.0019) | 0.1 (0.003) | |
| Connecting rod big end side clearance mm (in) | 0.10 - 0.25 (0.003 - 0.009) | 0.4 (0.02) | |
| Crankshaft, flywheel and drive plate | |||
| Crankshaft end play mm (in) | 0.05 - 0.25 (0.002 - 0.009) | 0.3 (0.01) | |
| Crankshaft journal outside diameter mm (in) | 60 (2.4) | - | |
| Crankshaft pin outside diameter mm (in) | 50 (2.0) | - | |
| Crankshaft journal oil clearance mm (in) | 0.02 - 0.04 (0.0008 - 0.0015) | 0.1 (0.003) | |
| Piston to cylinder clearance mm (in) | 0.02 - 0.04 (0.0008 - 0.0015) | - | |
| Cylinder block flatness of gasket surface mm (in) | 0.05 (0.02) | 0.1 (0.003) | |
| Cylinder block grinding limit of gasket surface mm (in) total resurfacing depth of both cylinder head and cylinder block | - | 0.2 (0.008) | |
| Cylinder block overall height mm (in) | 210.5 (8.29) | - | |
| Cylinder bore inside diameter mm (in) | 91.1 (3.59) | - | |
| Cylindricity mm (in) | 0.01 (0.0003) | - | |