LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2001 >> Sebring LX, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 52 (3.0L Engine (Service Information) - Coupe) >> Rocker Arms And Camshaft >> Inspection >> Lash Adjusters

Lash Adjusters

WARNING: This page is about a different car, the 2005 Dodge Stratus and 2005 Chrysler Sebring. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
  • The lash adjusters are precision-engineered mechanisms. Do not allow them to become contaminated by dirt or other foreign substances.
  • Do not attempt to disassemble the lash adjusters.
  • Use only fresh diesel fuel to clean the lash adjusters.
  1. Prepare three containers and approximately 5 dm3 (30.5 quart) of diesel fuel. Into each container, pour enough diesel fuel to completely cover a lash adjuster when it is standing upright. Then, perform the following steps with each lash adjuster.
    Fig 1: Identifying Containers Of Diesel Fuel
    G04538425Courtesy of DAIMLERCHRYSLER CORPORATION
  2. Place the lash adjuster in container A and clean its outside surface.
    NOTE: Use a nylon brush if deposits are hard to remove.
    Fig 2: Cleaning Outside Surface
    G04538426Courtesy of DAIMLERCHRYSLER CORPORATION
    CAUTION: The steel ball spring is extremely weak, so the lash adjuster's functionality may be lost if the air bleed wire is pushed in hard.
  3. While gently pushing down the internal steel ball using wire [0.5 mm (0.020 inch) in diameter] or special tool MD998442, move the plunger through five to ten strokes until it slides smoothly. In addition to eliminating stiffness in the plunger, this operation will remove dirty oil.
    NOTE: If the plunger remains stiff or the mechanism appears otherwise abnormal, replace the lash adjuster.
    Fig 3: Pushing Down Internal Steel Ball
    G04538427Courtesy of DAIMLERCHRYSLER CORPORATION
  4. Remove the lash adjuster from the container. Then, push down the steel ball gently and push the plunger to eliminate diesel fuel from the pressure chamber.
    Fig 4: Removing Lash Adjuster From Container
    G04538428Courtesy of DAIMLERCHRYSLER CORPORATION
    CAUTION: The steel ball spring is extremely weak, so the lash adjuster's functionality may be lost if the air bleed wire is pushed in hard.
  5. Place the lash adjuster in container B. Then, gently push down the internal steel ball using wire [0.5 mm (0.020 inch) in diameter] or special tool MD998442 and move the plunger through five to ten strokes until it slides smoothly. This operation will clean the lash adjuster's pressure chamber.
    Fig 5: Placing Lash Adjuster In Container B
    G04538429Courtesy of DAIMLERCHRYSLER CORPORATION
  6. Remove the lash adjuster from the container. Then, push down the steel ball gently and push the plunger to eliminate diesel fuel from the pressure chamber.
    Fig 6: Pushing Plunger To Eliminate Diesel Fuel From Pressure Chamber
    G04538430Courtesy of DAIMLERCHRYSLER CORPORATION
    CAUTION: Do not use container C for cleaning. If cleaning is performed in container C, foreign matter could enter the pressure chamber when the chamber is filled with diesel fuel.
  7. Place the lash adjuster in container C. Then, gently push down the internal steel ball using wire [0.5 mm (0.020 inch) in diameter] or special tool MD998442.
    Fig 7: Placing Lash Adjuster In Container C
    G04538431Courtesy of DAIMLERCHRYSLER CORPORATION
  8. Stand the lash adjuster with its plunger at the top, then push the plunger downward firmly until it moves through its greatest possible stroke. Return the plunger slowly, then release the steel ball and allow the pressure chamber to fill with diesel fuel.
    Fig 8: Releasing Steel Ball
    G04538432Courtesy of DAIMLERCHRYSLER CORPORATION
  9. Remove the lash adjuster from the container, then stand the lash adjuster with its plunger at the top. Push the plunger firmly and check that it does not move. Also, check that the lash adjuster's height matches that of a new lash adjuster.
    NOTE: If the lash adjuster contracts or moves, perform the operations 7 through 9 again to fill it with diesel fuel completely. Replace the lash adjuster if it still contracts or moves after performing these steps.
  10. Stand the lash adjuster upright to prevent diesel fuel from spilling out. Do not allow the lash adjuster to become contaminated by dirt or other foreign matter. Fit the lash adjuster onto the engine as soon as possible.
    Fig 9: Checking Lash Adjuster Height
    G04538433Courtesy of DAIMLERCHRYSLER CORPORATION