LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2001 >> Sebring LX, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 22 (2.4L Engine - On-Vehicle Service - Coupe) >> Special Tools

Special Tools

WARNING: This page is about a different car, the 2005 Dodge Stratus and 2005 Chrysler Sebring. However, it is still accessible from the selected car via links, so may be relevant.
SPECIAL TOOLS SPECIFICATION

TOOL TOOL NUMBER AND NAME REPLACED BY MILLER TOOL NUMBER APPLICATION
G04538097
 MB991502
Scan tool (MUT-II)		 DRB-III
Used with CH8425
  • Drive belt tension check
  • Ignition timing check
  • Curb idle speed check
  • Idle mixture check
  • Erasing the diagnostic trouble code
G04538098
 MB991668
Belt tension meter set		 N/A Drive belt tension check (used together with scan tool < MUT-II >)
G04538099
 MB991453
Engine hanger attachment set		 C-4852 When an engine lifer is used: Supporting the engine assembly during removal and installation of the transaxle (Use with MZ203827 and MB991453)
G04538100
 GENERAL SERVICE TOOL
MZ203827
Engine lifter		 N/A
G04538101
 MB991454
Engine hanger balancer		 N/A When the engine hanger is used: Supporting the engine assembly during remove and installation of the transaxle
NOTE: Special tool MB991454 is a part of engine hanger attachment set MB991453.
G04538102
 MB991895
Engine hanger		 N/A
G04538103
 MB991928
Engine hanger
  1. MB991929 Joint (50) x 2
  2. MB991930 Joint (90) x 2
  3. MB991931 Joint (140) x 2
  4. MB991932 Foot (standard) x 4
  5. MB991933 Foot (short) x 2
  6. MB991934 Chain and hook assembly
 N/A
G04538104
 MB990767
End yoke holder		 6847 Used with 8599 Holding the camshaft sprocket when loosening and tightening bolt (Use with MD998719)
G04538105
 MD998719
Crankshaft pulley holder pin		 8599 Supporting the camshaft sprocket when loosening and tightening bolt (Use with MB990767)
G04538106
 MD998443
Lash adjuster holder (8)		 MD998443 Supporting of the lash adjuster to prevent it from falling when rocker shaft assembly is removed or installed
G04538107
 MD998713
Camshaft oil seal installer		 MD998713
Used with 8618 screw		 Camshaft oil seal installation
G04538108
 MD998727
Oil pan FIPG cutter		 N/A Oil pan removal
G04538109
 MB991367
Special spanner		 6958 Holding the crankshaft sprocket when loosening and tightening bolt
G04538110
 MD998375
Crankshaft oil seal installer		 C-3095-A Crankshaft front oil seal installation
G04538111
 MD998781
Flywheel stopper		 N/A Flywheel < M/T > or drive plate < A/T > supporting
G04538112
 MD998776
Crankshaft rear oil seal installer		 MD998776-A
Used with C-4171		 Crankshaft rear oil seal installation (Use with MB990938)
G04538113
 MB990938
Handle		 C-4171 Crankshaft rear oil seal installation (Use with MD998776)
G04538114
 MB991654
Cylinder head bolt wrench (12)		 N/A Removal and installation of cylinder head bolt
G04538115
 MD998767
Tensioner pulley socket wrench		 MD998767 Timing belt tension adjustment
scientia non olet · About LEMON Manuals