LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2001 >> Sebring LX, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 14 (Body Diagnostic Procedures - Except Coupe) >> Diagnostic Information And Procedures >> Communication >> Symptom: *NO RESPONSE FROM TRAVELER (CMTC) >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2005 Dodge Stratus and 2005 Chrysler Sebring. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC PROCEDURES - NO RESPONSE FROM TRAVELER (CMTC)

TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRB, enter Body then Body Computer.
With the DRB, enter Body then Electro/Mech Cluster.
Was the DRB able to I/D or communicate with the BCM and the MIC?
Yes --> Go To 2
No --> Refer to the symptom list for problems related to no communication with the BCM or the MIC.
Perform BODY VERIFICATION TEST - VER 1 .		 All
2 Turn the ignition off.
Disconnect the Compass/Mini Trip Computer harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch Output circuit.
Is the test light illuminated?
Yes --> Go To 3
No --> Repair the Fused Ignition Switch Output circuit for an open or short. Refer to appropriate SYSTEM WIRING DIAGRAMS article.
Perform BODY VERIFICATION TEST - VER 1 .		 All
3 Turn the ignition off.
Disconnect the Compass/Mini Trip Computer harness connector.
Using a 12-volt test light connected to ground, probe the Fused B+ circuit.
Is the test light illuminated?
Yes --> Go To 4
No --> Repair the Fused B+ circuit for an open or short. Refer to appropriate SYSTEM WIRING DIAGRAMS article.
Perform BODY VERIFICATION TEST - VER 1 .		 All
4 Turn the ignition off.
Disconnect the Compass/Mini Trip Computer harness connector.
Using a 12-volt test light connected to 12-volts, probe the ground circuit.
Is the test light illuminated?
Yes --> Go To 5
No --> Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1 .		 All
5
NOTE: Ensure there is PCI Bus communication with other modules on the vehicle before proceeding. If not, refer to the appropriate test and repair as necessary.
Disconnect the Compass/Mini Trip Computer harness connector.Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and black test probes.Connect the scope input cable to the channel one connector on the DRB. Attach the red and black leads and the cable to probe adapter to the scope input cable.With the DRBIII®, select Pep Module Tools.Select lab scope.Select Live Data.Select 12 volt square wave.Press F2 for Scope.Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again when complete.Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus circuit in the CMTC connector.Turn the ignition on.Observe the voltage display on the DRB Lab Scope.Does the voltage pulse from 0 to approximately 7.5 volts?Yes --> Replace the Compass/Mini Trip Computer in accordance with the service information.Perform BODY VERIFICATION TEST - VER 1 .No --> Go To 6		 All
6 Turn the ignition off.
Disconnect the Compass/Mini Trip Computer harness connector.
Disconnect the Instrument Cluster harness connector.
Measure the resistance of the PCI Bus circuit between the CMTC connector and the Instrument Cluster connector (cav 3).
Is the resistance below 5.0 ohms?
Yes --> Replace the Instrument Cluster in accordance with the service information.
Perform BODY VERIFICATION TEST - VER 1 .
No --> Repair the PCI Bus circuit for an open.
Perform BODY VERIFICATION TEST - VER 1 .		 All
scientia non olet · About LEMON Manuals