Installation Procedure

Courtesy of GENERAL MOTORS COMPANY

Brake Pressure Modulator Valve Front Brake Pipe (2) @ Vehicle - Install
Brake Pressure Modulator Valve Front Brake Pipe Clip (1) - Secure [2x]
Courtesy of GENERAL MOTORS COMPANY

Brake Pressure Modulator Valve Front Brake Pipe Clip (1) - Secure
Courtesy of GENERAL MOTORS COMPANY

Front Brake Hose Retainer (2) - Install

CAUTION:

Fastener Caution

Brake Pressure Modulator Valve Front Brake Pipe Fitting (1) @ Front Brake Hose (3) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Remove the plug from the brake pressure modulator valve port.
Brake Pressure Modulator Valve Front Brake Pipe Fitting (1) @ Brake Pressure Modulator Valve - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Dash Panel Outer Insulator (3) - Install
Dash Panel Outer Insulator Retainer (2) - Install [5x]
Dash Panel Outer Insulator Retainer (1) - Install [2x]
Courtesy of GENERAL MOTORS COMPANY

Battery Tray Bracket (3) - Install
Battery Tray Bracket Nut (2) - Install and tighten - Fastener Specifications
Battery Tray Bracket Bolt (1) - Install and tighten [2x] - Fastener Specifications
Connect any harness retainers to the battery tray bracket.
Courtesy of GENERAL MOTORS COMPANY

Battery Tray (2) - Install
Battery Tray Bolt (1) - Install and tighten [4x] - Fastener Specifications
Connect any harness retainers attached to the battery tray.
Courtesy of GENERAL MOTORS COMPANY

Air Cleaner Assembly (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Air Cleaner Outlet Front Duct (2) @ Air Cleaner Assembly (3) - Install
Air Cleaner Clamp (1) - Tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Wiring Harness Retainer (2) - Install
Electrical Connector (1) - Connect
Courtesy of GENERAL MOTORS COMPANY

Turbocharger Wastegate Actuator Vacuum Control Solenoid Valve Filter Hose (1) @ Air Cleaner Assembly (2) - Install
Courtesy of GENERAL MOTORS COMPANY

Intake Air Duct (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Intake Air Duct Retainer (1) - Install [2x]
Courtesy of GENERAL MOTORS COMPANY

Battery (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Battery Hold Down Retainer (2) - Install
Battery Hold Down Bolt (1) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Battery Hold Down Retainer (3) - Install
Battery Hold Down Nut (1) - Install and tighten - Fastener Specifications
Battery Hold Down Bolt (2) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Battery Distribution Engine Compartment Fuse Block (2) - Install
Engage the retaining tabs.
Battery Positive Post Clamp Nut (1) - Tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Body Wiring Harness (6) - Install
Engine Wiring Harness (5) - Install
Battery Positive Cable (4) - Install
Body Wiring Harness Terminal Nut (3) - Tighten [4x] - Fastener Specifications
Engine Wiring Harness Terminal Nut (2) - Tighten - Fastener Specifications
Battery Positive Cable Nut (1) - Tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Electrical Connector (1) - Connect
Courtesy of GENERAL MOTORS COMPANY

Battery Distribution Engine Compartment Fuse Block Cover (1) - Install
Engage the retaining tabs.
Install the front tire and wheel assembly. Tire and Wheel Removal and Installation
Connect the battery negative cable. Battery Negative Cable Disconnection and Connection
Bleed the brake system. Hydraulic Brake System Bleeding (Pressure)
Lower the vehicle.
Fill the brake master cylinder reservoir to the maximum-full level with GM approved brake fluid from a clean, sealed brake fluid container. Brake Master Cylinder Reservoir Filling