Installation Procedure
Install the liftgate wiring harness (2) through the liftgate grommet opening and the roof panel grommet opening.
- Install the liftgate wiring harness grommet (1).
Install the wiring harness (2) and connect the retainer.
- Install the liftgate wiring harness grommet (1) to the roof panel.
Connect all the connectors of the liftgate wiring harness (2).
- Install the liftgate wiring harness grommet (1) to the liftgate.
{If equipped} Connect the electrical connector.
- Liftgate Lower Trim Finish Panel (1) - Remove
Liftgate Upper Side Trim Finish Panel (1) - Both Sides - Install [2x]
Liftgate Upper Center Trim Finish Panel (1) - Install
Install the liftgate trim finish panel pull cup (2).
- Liftgate Lower Trim Finish Panel Bolt (1) - Install and tighten - Fastener Specifications
Headlining Trim Panel (2) - Install
- Headlining Trim Panel Retainer (1) - Install [2x]
Retaining Clip (1) - Install [3x]
- Install the sunroof housing front drain hoses.
Retaining Clip (1) - Install [5x]
- Install the sunroof housing front drain hoses.
- NOTE:
Left side shown, right side similar.
Install the retainer that attaches the sunshade to the headliner.
- Sunshade - Left Side and Right Side (2) - [2x] Install
- Sunshade Bolt - Left Side and Right Side (1) - Install and tighten [4x] - Fastener Specifications
- NOTE:
Left side shown, right side similar.
Sunshade Retainer Bolt Cover - Left Side and Right Side (1) - Install [2x]
- NOTE:
Left side shown, right side similar.
Sunshade Support - Left Side and Right Side (2) - Install [2x]
- Sunshade Support Bolt - Left Side and Right Side (1) - Install and tighten [2x] - Fastener Specifications
- Close the sunshade support bolt access covers.
Windshield Multifunction Sensor Mount Bracket Cover (1) - Install
Windshield Multifunction Sensor Mount Bracket Cover Insert (1) - Install
- NOTE:
Reassemble the roof console if it becomes separated upon removal.
Connect the electrical connectors.
- Roof Console (1) - Install
Connect the electrical connector.
- Rear Seat Position Center Courtesy Lamp (1) - Install
Roof Rail Rear Assist Handle - Left Side and Right Side (2) - Install [2x]
- Roof Rail Rear Assist Handle Bolt - Left Side and Right Side (1) - Install and tighten [4x] - Fastener Specifications
Roof Rail Assist Handle (2) - Install
- Roof Rail Assist Handle Bolt (1) - Install and tighten [2x] - Fastener Specifications
- NOTE:
Left side shown, right side similar.
Body Lock Pillar Upper Trim Panel - Left Side and Right Side (2) - Install [2x]
- Quarter Window Trim Finish Panel Bolt - Left Side and Right Side (1) - Install and tighten [2x] - Fastener Specifications
- Close the quarter window trim finish panel bolt caps.
- NOTE:
Left side shown, right side similar.
Center Pillar Upper Trim Panel - Left Side and Right Side (2) - Install [2x]
- Center Pillar Upper Garnish Molding Bolt - Left Side and Right Side (1) - Install and tighten [2x] - Fastener Specifications
- Close the center pillar upper trim panel bolt caps.
Center Pillar Lower Trim Panel (1) - Install
Rear Side Door Sill Garnish Molding (1) - Install
Front Side Door Sill Garnish Molding (2) - Install
Connect the electrical connectors. [2x]
- Windshield Garnish Molding Bolt - Left Side and Right Side (2) - Install and tighten [2x] - Fastener Specifications
- Align the retainer clips with the slots in the A pillar and press the windshield garnish molding (1) into place.
- Windshield Garnish Molding - Left Side and Right Side (1) - Install [2x]
- Reposition the weatherstrip as necessary.
- Enable the SIR System. SIR Disabling and Enabling
Refer to Fastener Caution .