Removal Procedure
With a flat bladed plastic trim tool, start at the front and work your way back to release the clips.
- Instrument Panel Outer Trim Cover - Left Side (1) - Remove
Hood Primary Latch Release Cable Handle (1) @ Instrument Panel Knee Bolster - Remove
Instrument Panel Knee Bolster Bolt (1) - Remove [3x]
Using a flat-bladed tool, release instrument panel knee bolster (1).
- Instrument Panel Knee Bolster (1) - Remove
Instrument Panel Switch Trim Plate Bolt (1) - Remove
Using a flat-bladed tool, release instrument panel switch trim plate (1).
- Instrument Panel Switch Trim Plate (1) - Remove
- Disconnect the electrical connector.
- Extend the steering column to its furthest point to allow the instrument panel steering column upper trim cover to clear the instrument panel.
With a flat bladed plastic trim tool, release the retaining clips.
- Instrument Panel Cluster Trim Plate (1) - Remove
Instrument Panel Trim Plate Strap Bolt (1) - Remove [4x]
- Instrument Panel Instrument Cluster Hood (2) - Remove
With a flat bladed plastic trim tool, release the retaining clips.
With a flat bladed plastic trim tool, release the retaining clips.
- Instrument Panel Bolt Cover - Right Side (1) - Remove
- Instrument Panel Bolt Cover - Left Side (1) - Remove
Driver Information Display Bolt (1) - Remove [5x]
Driver Information Display (1) - Remove
- Disconnect the electrical connectors.
Using a small plastic trim tool, separate the instrument panel steering column upper trim cover (1) from the instrument panel steering column lower trim cover.
Instrument Panel Trim Plate Applique Bolt (1) - Remove
- Release the retainers with a suitable plastic trim tool.
- Instrument Panel Trim Plate Applique - Left Side (2) - Remove
Using a flat-bladed tool, release instrument panel center trim plate applique (1).
- Instrument Panel Center Trim Plate Applique (1) - Remove
- Disconnect the electrical connector.
Heater and Air Conditioning User Interface Control Bolt (1) - Remove [2x]
- Disconnect the electrical connector.
- Heater and Air Conditioning User Interface Control (2) - Remove
Instrument Panel Trim Plate Applique Bolt (1) - Remove [4x]
Using a flat-bladed tool, release instrument panel trim plate applique (1).
- Instrument Panel Trim Plate Applique - Right Side (1) - Remove
- Disconnect the electrical connector.
With a flat bladed plastic trim tool, start at the front and work your way back to release the clips.
- Instrument Panel Outer Trim Cover - Right Side (1) - Remove
Instrument Panel Outer Air Outlet Bolt (1) - Remove [2x]
- Instrument Panel Outer Air Outlet - Right Side (2) - Remove
Open the instrument panel compartment door.
- Instrument Panel Compartment Door (2) @ Instrument Panel Compartment Door Dampener (1) - Disconnect
Lift the instrument panel compartment door (1) up using a suitable tool and take the instrument panel compartment door (1) out from the instrument panel compartment.
Instrument Panel Compartment Door (1) - Remove
Instrument Panel Lower Insulator Retainer (1) - Remove [2x]
- Instrument Panel Lower Insulator Bolt (2) - Remove
- Instrument Panel Lower Trim Panel Insulator (3) - Remove
Using a flat-bladed tool, release instrument panel accessory bezel (1).
- Instrument Panel Accessory Bezel (1) - Remove
- Disconnect the electrical connectors.
Front Floor Console (1) - Remove - Front Floor Console Removal and Installation
Front Floor Console Storage Tray Bolt (1) - Remove [2x]
Front Floor Console Stowage Tray (1) - Remove
{With K4C} Disconnect the electrical connector. (1)
{With K4C} Instrument Panel Compartment Air Duct (1) - Disconnect
Instrument Panel Compartment Bolt (1) - Remove [12x]
Instrument Panel Compartment (1) - Remove