LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2023 >> Tahoe SSV >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 11 (Engine Mechanical - 3.0L (Lm2) Diesel - Repair Instructions (1 Of 11)) >> Repair Instructions >> Engine Front Cover Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different variant/trim than selected.
  1. GM5877076Courtesy of GENERAL MOTORS COMPANY

    Install the engine front cover (1) from the bottom of the vehicle.

  2. GM5591893Courtesy of GENERAL MOTORS COMPANY

    {without RC1} Install the front bumper fascia extension.

      NOTE:

      Quantity of fasteners may vary based on option content.

    1. Front Bumper Fascia Extension (4) - Install
      2. CAUTION:

      Refer to Fastener Caution .

    2. Front Bumper Fascia Extension Bolt (3) @Underbody Skid Shield - Install and tighten [2x] - Fastener Specifications
    3. Front Bumper Fascia Extension Bolt (2) - Install and tighten [4x] - Fastener Specifications
    4. GM5540946Courtesy of GENERAL MOTORS COMPANY

      Front Bumper Fascia Extension (1) - Install

    5. GM5540945Courtesy of GENERAL MOTORS COMPANY

      Front Bumper Fascia Extension Bolt (2) - Install and tighten [8x] - Fastener Specifications

    6. Front Bumper Fascia Air Deflector Bolt (1) - Install and tighten [10x] - Fastener Specifications
  3. GM5519593Courtesy of GENERAL MOTORS COMPANY

    {with RC1} Install the underbody splash shield.

    1. Underbody Splash Shield (1) - Install
    2. GM5519590Courtesy of GENERAL MOTORS COMPANY

      Underbody Splash Shield Bolt (2) - Install and tighten [4x] - Fastener Specifications

    3. Front Bumper Fascia Skid Plate Bolt (1) - Install and tighten [4x] - Fastener Specifications
  4. Lower the vehicle.
  5. GM5619156Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Some components not shown for graphic clarity.

    Push down and rearward on the engine front cover (2) to engage the 5 retaining grommets to the ball studs.

  6. Engine Front Cover Bolt (1) - Install and tighten - Fastener Specifications
  7. GM5572432Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Left side shown, right side similar.

    Front End Sheet Metal Diagonal Brace- Left Side and Right Side (2) - Install [2x]

  8. If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
    1. Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
    2. Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
  9. Front End Sheet Metal Diagonal Brace Bolt- Left Side and Right Side (1) - Install and tighten [4x] - Fastener Specifications
  10. GM5617832Courtesy of GENERAL MOTORS COMPANY

    Intake Air Splash Shield (2) - Install

  11. Intake Air Baffle Retainer (1) - Install [9x]
  12. GM5541781Courtesy of GENERAL MOTORS COMPANY

    { If equipped }Hood Secondary Latch Release Handle (2) - Install

  13. { If equipped }Hood Latch Actuator Bolt (1) - Install and tighten [2x] - Fastener Specifications
  14. Oil Filler Cap - Remove
  15. GM5171779Courtesy of GENERAL MOTORS COMPANY

    Intake Manifold Cover (2) - Install

  16. Intake Manifold Cover Bolt (1) - Install and tighten - Fastener Specifications
  17. Oil Filler Cap - Install
scientia non olet · About LEMON Manuals