LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2023 >> Tahoe SSV >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 10 (Engine Controls And Fuel - 3.0L (Lm2) Diesel - Diagnostic Information And Procedures (5 Of 5)) >> Diagnostic Information and Procedures >> DTC P2B5E, P2B5F, or U063F >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different variant/trim than selected.
    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: Q97M Engine Coolant Flow Control Valve - Main
  3. Test for less than 10 ohms between the test points: Low Reference circuit terminal 5 & Ground
    • If 10 ohms or greater 
    1. Disconnect the electrical connector: X1@K20 Engine Control Module
    2. Test for less than 2 ohms between the test points: Low Reference circuit terminal 5@Component harness & Terminal 79 X1@ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K20 Engine Control Module
    • Go to next step: If less than 10 ohms 
  4. Ignition - On/Vehicle - In Service Mode
  5. Test for 4.8 to 5.2 V between the test points: 5 V Reference circuit terminal 3 & Low Reference circuit terminal 5
    • If less than 4.8 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: X1@K20 Engine Control Module
    3. Test for infinite resistance between the test points: 5 V Reference circuit terminal 3@ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    4. Test for less than 2 ohms between the test points: 5 V Reference circuit terminal 3@ Component harness & Terminal 3 X1@ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K20 Engine Control Module
    • If greater than 5.2 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: X1@K20 Engine Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: 5 V Reference circuit terminal 3@Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K20 Engine Control Module
    • Go to next step: If between 4.8 and 5.2 V 
  6. Test for 4.8 to 5.2 V between the test points: Signal circuit terminal 4 & Ground
    • Go to next step: If less than 4.8 V 
    1. Disconnect the electrical connector: X1@K20 Engine Control Module
    2. Test for infinite resistance between the test points: Signal circuit terminal 4@Component harness & Ground
      • If less than infinite resistance

        Repair the short to ground on the circuit:

      • Go to next step: If infinite resistance
    3. Test for infinite resistance between the test points: Signal circuit terminal 4@Component harness & Low Reference circuit terminal 5@Component harness
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    4. Test for less than 2 ohms between the test points: Signal circuit terminal 4@Component harness & Terminal 57 X1@Control module harness
      • If 2 ohms or greater

        Repair the open/high resistance in the circuit:

      • Go to next step: If less than 2 ohms

        Go to next step: Replace the component: K20 Engine Control Module

    • If greater than 5.2 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: X1@K20 Engine Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 4@Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K20 Engine Control Module
    • Go to next step: If between 4.8 and 5.2 V 
  7. Replace the component: Q97M Engine Coolant Flow Control Valve - Main
scientia non olet · About LEMON Manuals