Single Use Fasteners and Components

WARNING: This page is about a different variant/trim than selected.

Catalytic Converter Gasket
Catalytic Converter Gasket@Exhaust Muffler Assembly
Clutch Pressure Plate Bolt [6x]
Flywheel Bolt [8x]

Fig 1: Engine Flywheel With Flywheel Bolt Tightening Sequence

Courtesy of GENERAL MOTORS COMPANY

NOTE: Callouts items in the following chart represent components shown in graphic above.

Callout	Component Name
Preliminary Procedure Clutch Assembly Replacement (M13) , or Clutch Assembly Replacement (MJK, MH3, MM6)
1	Engine Flywheel Bolt [8x] CAUTION: This vehicle is equipped with torque-to-yield or single use fasteners. Install a NEW torque-to-yield or single use fastener when installing this component. Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component. CAUTION: Refer to Fastener Caution . Procedure Install the NEW bolts loosely by hand. If necessary, remove EN-51701-2 holder and rotate the secondary mass using EN-51701-1 aligner and a breaker bar to align the holes in the secondary mass with the primary mass. To prevent crankshaft rotation, install EN-50792 holding tool and starter motor bolts at the starter motor location, engaging the flywheel. Tighten the bolts evenly using the following procedure: NOTE: Fasteners have adhesive patch and must be tightened to final torque within 5 minutes. Tighten Tighten the bolts a first pass in sequence to 30 N.m (22 lb ft). Tighten the bolts a final pass in sequence 80 degrees using the EN-45059 meter. Special Tools EN-45059 Angle Meter EN-50792 Flywheel Holding Tool EN-51701 Flywheel Aligner and Holder Equivalent regional tools: Special Tools
2	Engine Flywheel Procedure Clean and inspect flywheel. Flywheel Cleaning and Inspection NOTE: EN-51701-2 holder and EN-51701-1 aligner may be installed on the flywheel to maintain alignment of the secondary mass to the primary mass. Special Tools EN-51701 Flywheel Aligner and Holder Equivalent regional tools: Special Tools

Callout

Component Name

Preliminary Procedure
Clutch Assembly Replacement (M13) , or Clutch Assembly Replacement (MJK, MH3, MM6)

Engine Flywheel Bolt [8x]

CAUTION:

This vehicle is equipped with torque-to-yield or single use fasteners. Install a NEW torque-to-yield or single use fastener when installing this component. Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.

CAUTION:

Refer to Fastener Caution .

Procedure

Install the NEW bolts loosely by hand. If necessary, remove EN-51701-2 holder and rotate the secondary mass using EN-51701-1 aligner and a breaker bar to align the holes in the secondary mass with the primary mass.
To prevent crankshaft rotation, install EN-50792 holding tool and starter motor bolts at the starter motor location, engaging the flywheel.
Tighten the bolts evenly using the following procedure:
NOTE:
Fasteners have adhesive patch and must be tightened to final torque within 5 minutes.

Tighten
1. Tighten the bolts a first pass in sequence to 30 N.m (22 lb ft).
2. Tighten the bolts a final pass in sequence 80 degrees using the EN-45059 meter.

Special Tools

EN-45059 Angle Meter
EN-50792 Flywheel Holding Tool
EN-51701 Flywheel Aligner and Holder

Equivalent regional tools: Special Tools

Engine Flywheel
Procedure
Clean and inspect flywheel. Flywheel Cleaning and Inspection

NOTE:

EN-51701-2 holder and EN-51701-1 aligner may be installed on the flywheel to maintain alignment of the secondary mass to the primary mass.

Special Tools
EN-51701 Flywheel Aligner and Holder
Equivalent regional tools: Special Tools