Removal Procedure

WARNING: This page is about a different variant/trim than selected.

Drain the cooling system. Cooling System Draining and Filling (Static LM2) , or Cooling System Draining and Filling (GE 47716 LM2)
Plenum Front Panel Outer Reinforcement - Remove - Plenum Front Panel Outer Reinforcement Removal and Installation
Courtesy of GENERAL MOTORS COMPANY

Air Cleaner Outlet Duct Clamp (1) - Loosen [2x]
Air Cleaner Outlet Front Duct (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Oil Filler Cap - Remove
Intake Manifold Cover Bolt (1) - Remove
Intake Manifold Cover (2) - Remove
Install the oil filler cap after removal of the intake manifold cover (2) to prevent debris from falling into the engine.
Courtesy of GENERAL MOTORS COMPANY

Air Cleaner Outlet Duct Clamp (1) - Loosen
Air Cleaner Outlet Duct (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Remove the 3 rear engine wiring harness channel nuts (1).
Position the rear engine wiring harness channel (2) out of the way.
Courtesy of GENERAL MOTORS COMPANY

Remove the engine coolant outlet pipe bracket bolt (1) and position the engine coolant air bleed hose (2) out of the way.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Note: Support the exhaust gas recirculation pipe when loosening/tightening the bolts to ensure the pipe is not deformed.

Exhaust Gas Recirculation Cooler Bolt (1) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Turbocharger Coolant Feed Pipe Bolt (3) - Remove
Courtesy of GENERAL MOTORS COMPANY

Remove the turbocharger coolant return hose clip (1) and position the turbocharger coolant return hose out of the way.
Exhaust Gas Recirculation Outlet Pipe Bolt (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Exhaust Gas Recirculation Outlet Pipe Bolt (1) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Exhaust Gas Recirculation Cooler Outlet Pipe (1) - Remove
Exhaust Gas Recirculation Pipe Seal (2) - Remove and DISCARD
Exhaust Gas Recirculation Cooler Inlet Pipe Gasket (3) - Remove and DISCARD
Courtesy of GENERAL MOTORS COMPANY

Hose Clamp (1) - Disengage - Hose Clamp Replacement Guidelines - Spring Type
Exhaust Gas Recirculation Manifold Cooling Return Hose (2) @ Exhaust Gas Recirculation Cooler Inlet Pipe - Reposition
Courtesy of GENERAL MOTORS COMPANY

Hose Clamp (1) - Disengage [2x] - Hose Clamp Replacement Guidelines - Spring Type
Exhaust Gas Recirculation Valve Cooling Return Hose (2) @ Exhaust Gas Recirculation Cooler Inlet Pipe - Remove
Thermostat Bypass Hose (3) @ Exhaust Gas Recirculation Cooler Inlet Pipe - Remove
Courtesy of GENERAL MOTORS COMPANY

Exhaust Gas Recirculation Valve Cooling Feed Hose Clamp (1) - Disengage - Hose Clamp Replacement Guidelines - Spring Type
Exhaust Gas Recirculation Valve Cooling Feed Hose (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Exhaust Gas Recirculation Manifold Cooling Return Hose (2) @ Exhaust Gas Recirculation Pipe Clip (1) - Separate
Exhaust Gas Recirculation Cooler Water Bypass Inlet Hose (3) @ Exhaust Gas Recirculation Pipe Clip (1) - Separate
Courtesy of GENERAL MOTORS COMPANY

Exhaust Gas Recirculation Valve Cooling Feed Hose Clamp (2) - Disengage - Hose Clamp Replacement Guidelines - Spring Type
Remove the exhaust gas recirculation valve cooling return hose (3) from the exhaust gas recirculation valve.
Courtesy of GENERAL MOTORS COMPANY

Disconnect the exhaust gas recirculation valve electrical connector.
Exhaust Gas Recirculation Valve Bolt (1) - Remove [2x]
Remove the exhaust gas recirculation valve (2) with the exhaust gas recirculation cooler inlet pipe.
Exhaust Gas Recirculation Valve Inlet Gasket (3) - Remove and DISCARD
Courtesy of GENERAL MOTORS COMPANY

Exhaust Gas Recirculation Pipe Bracket Bolt (1) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Exhaust Gas Recirculation Cooler Inlet Pipe (1) - Remove