LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2022 >> Tahoe PPV, RWD >> Repair and Diagnosis >> Accessories & Equipment >> Interior/Exterior Trim >> Seat Hardware, Trim, And Upholstery >> Repair Instructions >> Rear Seat Frame Replacement (40 Percent, Bucket) >> Removal Procedure

Removal Procedure

  1. GM5604908Courtesy of GENERAL MOTORS COMPANY

    Rear Seat (2) - Remove - Rear Seat Removal and Installation (Bucket) , or Rear Seat Removal and Installation (40 Percent) 

  2. GM5606266Courtesy of GENERAL MOTORS COMPANY

    Rear Seat Cushion Cover and Pad (1) Remove - Rear Seat Cushion Cover and Pad Removal and Installation (Bucket) , or Rear Seat Cushion Cover and Pad Removal and Installation (40 Percent) 

  3. GM5606233Courtesy of GENERAL MOTORS COMPANY

    Rear Seat Back Cover and Pad (1) - Remove - Rear Seat Back Cover and Pad Removal and Installation (Bucket) , or Rear Seat Back Cover and Pad Removal and Installation (40 Percent) 

  4. GM5606232Courtesy of GENERAL MOTORS COMPANY

    Using a suitable flat-bladed tool, push the plastic tab of the rear seat head restraint guide (1) inward and pull upward to remove from the seat back frame.

  5. Rear Seat Head Restraint Guide (1) - Remove [2x]
  6. GM5607844Courtesy of GENERAL MOTORS COMPANY

    Using a suitable trim tool, release the retainers.

  7. Rear Seat Back Cover Retainer (1) - Remove [4x]
  8. Rear Seat Back Panel (2) - Remove
  9. GM5599030Courtesy of GENERAL MOTORS COMPANY

    {If equipped} Disconnect and reposition harness as necessary.

  10. Rear Seat Belt Buckle Bolt (1) - Remove
  11. Rear Seat Belt Buckle (2) - Remove
  12. GM5599034Courtesy of GENERAL MOTORS COMPANY

    Using a flat-bladed plastic trim tool, release the retaining clips.

  13. Rear Seat Riser Finish Cover (1) - Remove
  14. GM5605358Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Left side shown, right side similar.

    Using a flat-bladed plastic trim tool, release the retaining clip.

  15. Rear Seat Riser Finish Cover (1) - Remove [2x]
  16. GM5599035Courtesy of GENERAL MOTORS COMPANY

    Using a flat-bladed plastic trim tool, release the retaining clips.

  17. Using a suitable plastic trim tool, release the retaining tabs.
  18. Rear Seat Riser Inner Finish Cover-Outboard (1) - Remove
  19. GM5599036Courtesy of GENERAL MOTORS COMPANY

    Using a flat-bladed plastic trim tool, release the retaining clips.

  20. Using a suitable plastic trim tool, release the retaining tabs.
  21. Rear Seat Riser Inner Finish Cover-Inboard (1) - Remove
  22. GM5605359Courtesy of GENERAL MOTORS COMPANY

    Rear Seat Latch Finish Cover (1) - Remove [2x]

  23. GM5605757Courtesy of GENERAL MOTORS COMPANY

    Release the remaining J-channel retainers on the rear seat cushion trim panel (2).

  24. Rear Seat Back Opening Finish Cover Retainer (1) - Remove [4x]
  25. GM5606804Courtesy of GENERAL MOTORS COMPANY

    Place the rear seat in the fold and tumble position.

  26. Rear Seat Cushion Trim Panel (1) - Remove
  27. GM5600940Courtesy of GENERAL MOTORS COMPANY

    Disconnect the wiring harness retainers and reposition the harness as necessary.

  28. Front Seat Bolt (1) - Remove [2x]
  29. Using a flat-bladed plastic trim tool, release the retaining clips.
  30. Rear Seat Track Finish Cover (2) - Remove
  31. GM5606897Courtesy of GENERAL MOTORS COMPANY

    {If equipped} Disconnect the electrical connectors.

  32. {If equipped} Front Seat Bolt (1) - Remove
  33. {If equipped} Release the rear seat heater vent control module retaining tabs.
  34. {If equipped} Rear Seat Heater Vent Control Module (2) - Remove
  35. GM5606900Courtesy of GENERAL MOTORS COMPANY

    Return the rear seat to the original position.

    36. NOTE:

    Note the location and routing of the seat cable to ensure proper installation.

  36. Release the folding rear seat back actuator cable (2) from the cable retainer (1).
  37. Disconnect the rear seat back actuator cable end from the rear seat frame.
  38. GM5606902Courtesy of GENERAL MOTORS COMPANY

    Disconnect the electrical connector.

  39. Rear Seat Riser Bolt (1) - Remove [3x]
  40. Folding Rear Seat Back Actuator (2) - Remove
  41. GM5606893Courtesy of GENERAL MOTORS COMPANY

    Disconnect the wiring harness retainers and reposition the harness as necessary.

  42. Front Seat Bolt (1) - Remove [4x]
  43. Rear Seat Heater Control Module Bracket (2) - Remove
  44. GM5605755Courtesy of GENERAL MOTORS COMPANY

    Using a flat-bladed plastic trim tool, release the retaining clips.

  45. Rear Seat Frame Rear Finish Cover (2) - Remove [2x]
  46. GM5605753Courtesy of GENERAL MOTORS COMPANY

    Rear Seat Riser Finish Cover Retainer (1) - Remove

  47. Rear Seat Back Cover Retainer (2) - Remove
  48. Rear Seat Recliner Inner Finish Cover (3) - Remove
  49. GM5605754Courtesy of GENERAL MOTORS COMPANY

    Rear Seat Riser Finish Cover Retainer (1) - Remove

  50. Rear Seat Back Cover Retainer (2) - Remove
  51. Rear Seat Recliner Inner Finish Cover (3) - Remove
  52. GM5605356Courtesy of GENERAL MOTORS COMPANY

    Depress the retaining tab while pulling the rear seat hinge finish cover (1) inward then upward to release from the rear seat hinge.

  53. Rear Seat Hinge Finish Cover-Outboard (1) - Remove
  54. GM5605357Courtesy of GENERAL MOTORS COMPANY

    Depress the retaining tab while pulling the rear seat hinge finish cover (1) inward then upward to release from the rear seat hinge.

  55. Rear Seat Hinge Finish Cover-Inboard (1) - Remove
  56. GM5605184Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Typical wiring harness shown, individual harness may be different due to option content. Various seat components may need to be removed from the seat to access the harness depending on seat and content options.

    Disconnect the electrical connectors and release the wiring harness retainers as necessary.

  57. Rear Seat Wiring Harness (1) - Remove
  58. GM5607842Courtesy of GENERAL MOTORS COMPANY

    Rear Seat Frame (1) - Remove

scientia non olet · About LEMON Manuals