LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2022 >> Camaro LS, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 26 (Automatic Transmission - 10L60, 10L80 Or 10L90 - Diagnostic Information And Procedures) >> Diagnostic Information and Procedures >> DTC P0721-P0723, P077C, P077D, P172A, or P172B >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different variant/trim than selected.
    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: X1 @ T12 Automatic Transmission Assembly
  3. Ignition - On/Vehicle - In Service Mode
  4. Test for 8.3 to 9.6 V between the test points: 9 V Reference circuit terminal 7 & Ground
    • If less than 8.3 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K71 Transmission Control Module
    3. Test for infinite resistance between the test points: 9 V Reference circuit terminal 7 @Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    4. Test for less than 2 ohms between the test points: 9 V Reference circuit terminal 7 @ Component harness & Terminal 7 @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K71 Transmission Control Module
    • If greater than 9.6 V 
    1. Connect the electrical connector.X1 @ T12 Automatic Transmission Assembly
    2. Ignition/Vehicle - Off
    3. Disconnect the electrical connector: X1 @ T12 Automatic Transmission Assembly
    4. Disconnect the electrical connector: K71 Transmission Control Module
    5. Ignition - On/Vehicle - In Service Mode
    6. Test for less than 1 V between the test points: 9 V Reference circuit terminal 7 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K71 Transmission Control Module
    • Go to next step: If between 8.3 and 9.6 V 
  5. Connect the electrical connector.X1 @ T12 Automatic Transmission Assembly
  6. Ignition/Vehicle - Off
  7. Disconnect the electrical connector: X1 @ T12 Automatic Transmission Assembly
  8. Install - EL-38522 Variable Signal Generator
    • Voltage - 5 V
    • Frequency - 300 Hz
    • Duty Cycle - 50%
    • Black lead @ Ground
    • Red lead @ Signal circuit terminal 4
  9. Ignition - On/Vehicle - In Service Mode
  10. Verify the scan tool parameter: Transmission OSS = 256 to 276 RPM
    • If not between 256 and 276 RPM 
    1. Connect the electrical connector.X1 @ T12 Automatic Transmission Assembly
    2. Ignition/Vehicle - Off
    3. Disconnect the electrical connector: X1 @ T12 Automatic Transmission Assembly
    4. Disconnect the electrical connector: K71 Transmission Control Module
    5. Ignition - On/Vehicle - In Service Mode
    6. Test for less than 1 V between the test points: Signal circuit terminal 4 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    7. Connect the electrical connector.X1 @ T12 Automatic Transmission Assembly
    8. Connect the electrical connector.K71 Transmission Control Module
    9. Ignition/Vehicle - Off
    10. Disconnect the electrical connector: X1 @ T12 Automatic Transmission Assembly
    11. Disconnect the electrical connector: K71 Transmission Control Module
    12. Test for infinite resistance between the test points: Signal circuit terminal 4 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    13. Test for less than 2 ohms between the test points: Signal circuit terminal 4 @ Component harness & Terminal 14 @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K71 Transmission Control Module
    • Go to next step: If between 256 and 276 RPM 
  11. Connect the electrical connector.X1 @ T12 Automatic Transmission Assembly
  12. Connect the electrical connector.K71 Transmission Control Module
  13. Ignition/Vehicle - Off
  14. Disconnect the electrical connector: X1 @ T12 Automatic Transmission Assembly
  15. Remove the component: Automatic Transmission Fluid Pan
  16. Connect the electrical connector.X1 @ T12 Automatic Transmission Assembly
  17. Disconnect the electrical connector: B14A Transmission Output Shaft Speed Sensor
  18. Ignition - On/Vehicle - In Service Mode
  19. Test for 8.3 to 9.6 V between the test points: 9 V Reference circuit terminal 2 & Ground
    • If not between 8.3 and 9.6 V 

      Replace the component: Automatic Transmission Wiring Harness

    • Go to next step: If between 8.3 and 9.6 V 
  20. Ignition/Vehicle - Off
  21. Install - EL-38522 Variable Signal Generator
    • Voltage - 5 V
    • Frequency - 300 Hz
    • Duty Cycle - 50%
    • Black lead@Ground
    • Red lead@Signal circuit terminal 1
  22. Ignition - On/Vehicle - In Service Mode
  23. Verify the scan tool parameter: Transmission OSS = 256 to 276 RPM
    • If not between 256 and 276 RPM 

      Replace the component: Automatic Transmission Wiring Harness

    • Go to next step: If between 256 and 276 RPM 
  24. Test or replace the component: B14A Transmission Output Shaft Speed Sensor
scientia non olet · About LEMON Manuals