LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2021 >> Trailblazer RS, 4WD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 9 (Engine Controls And Fuel - 1.0L (L4B L4F L4G LIJ) Or 1.2L (L4H L4K LIF LIH) - Diagnostic Information And Procedures (1 Of 2)) >> Diagnostic Information and Procedures >> DTC P0243, P0245, or P0246 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different variant/trim than selected.
  1. Ignition/Vehicle - Off
  2. Disconnect the electrical connector: Q42 Turbocharger Wastegate Solenoid Valve
  3. Connect a test lamp between the test points: Control circuit terminal 1 & Ground
  4. Ignition - On/Vehicle - In Service Mode
  5. Perform the scan tool control function: Turbocharger Wastegate Actuator - On and Off

    Verify the test lamp turns On and Off.

    • If the test lamp is always Off 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the appropriate electrical connector: K20 Engine Control Module
    3. Test for infinite resistance between the test points: Control circuit terminal 1 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    4. Test for less than 2 ohms between the test points: Control circuit terminal 1 @ Component harness & The other end of the circuit @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K20 Engine Control Module
    • If the test lamp is always On 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the appropriate electrical connector: K20 Engine Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Control circuit terminal 1 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K20 Engine Control Module
    • Go to next step: If the test lamp turns On and Off 
  6. Connect a test lamp between the test points: Control circuit terminal 1 & Control circuit terminal 2
  7. Perform the scan tool control function: Turbocharger Wastegate Actuator - On and Off

    Verify the test lamp turns On and Off.

    • If the test lamp is always Off 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the appropriate electrical connector: K20 Engine Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Control circuit terminal 2 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points: Control circuit terminal 2 @ Component harness & The other end of the circuit @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K20 Engine Control Module
    • If the test lamp is always On 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Test for infinite resistance between the test points: Control circuit terminal 2 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: K20 Engine Control Module
    • Go to next step: If the test lamp turns On and Off 
  8. Test or replace the component: Q42 Turbocharger Wastegate Solenoid Valve
scientia non olet · About LEMON Manuals