LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2021 >> Trailblazer RS, 4WD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Engine Mechanical - 1.2L (LIH)) >> Repair Instructions >> Propulsion System Lift Table >> Installation Procedure

Installation Procedure

WARNING: This page is about a different variant/trim than selected.
  1. Front Compartment Insulator - Remove - Front Compartment Insulator Replacement (Base)
  2. Transmission Mount Strut Bracket - Remove - Transmission Mount Strut Bracket Replacement (LIH)
  3. GM5084615Courtesy of GENERAL MOTORS COMPANY

    EN-52055-2  Double Spindle (1) @ EN-52055-1  Stand Tube (2) - Install [4x]

  4. GM5084634Courtesy of GENERAL MOTORS COMPANY

    EN-52055-8  Torque Support (1) @ EN-52055-1  Stand Tube (2) - Install

  5. GM5442630Courtesy of GENERAL MOTORS COMPANY

    EN-52055-9  Torque Support (1) @ EN-52055-1  Stand Tube (2) - Install

  6. GM5442628Courtesy of GENERAL MOTORS COMPANY

    Install the EN-52055-4  Support Tube (1) onto the EN-52055-2  Double Spindle / EN-52055-1  Stand Tube assembly. [2x]

    1. Install the support assembly onto the GE-52200  Propulsion System Lift Table aligned to the bore in the engine as shown
  7. Install the EN-52055-5  Flexible Support Tube (2) onto the EN-52055-2  Double Spindle / EN-52055-1  Stand Tube assembly. [2x]
    1. Install the support assembly onto the GE-52200  Propulsion System Lift Table aligned to the bore in the engine as shown
  8. Install the EN-52055-8  Torque Support / EN-52055-1  Stand Tube assembly (3)
    1. Install the support assembly onto the GE-52200  Propulsion System Lift Table aligned to the bore in the transmission using the remaining bolt and nut as shown.
  9. GM5442629Courtesy of GENERAL MOTORS COMPANY

    Adjust the EN-52055-6  Thread Bar (1) / EN-52055-1  Stand Tube (6) assembly aligned to the bore in the transmission as shown.

  10. Install the EN-52055-9  Torque Support (2) / EN-52055-1  Stand Tube (6) assembly
    1. Install the support assembly onto the GE-52200  Propulsion System Lift Table aligned to the bore in the transmission as shown.
  11. Install the EN-52055-5  Flexible Support Tube (3) onto the EN-52055-2  Double Spindle / EN-52055-1  Stand Tube (5) assembly.
    1. Install the support assembly onto the GE-52200  Propulsion System Lift Table aligned to the bore in the engine as shown
  12. Install the EN-52055-4  Support Tube (4) onto the EN-52055-2  Double Spindle / EN-52055-1  Stand Tube (5) assembly.
    1. Install the support assembly onto the GE-52200  Propulsion System Lift Table aligned to the bore in the engine as shown
    13. WARNING:

    The GE-52200-50 lift table limiting chain is for use with GE-52200 lifting tables not equipped with a mechanical stop. Refer to the operating instructions provided with the limiting chain. Failure to limit uncontrolled descent of the lifting table may result in damage and/or personal injury.

  13. Raise the GE-52200  Propulsion System Lift Table until:
    1. EN-52055-5  Flexible Support Tube and EN-52055-6  Thread Bar are inserted into and support the powertrain assembly.
    2. EN-52055-1  Stand Tube attach to the powertrain with EN-52055-4  Support Tube meet the GE-52200  Propulsion System Lift Table.
  14. Complete the engine replacement, refer to Engine Replacement 
scientia non olet · About LEMON Manuals