Installation Procedure
- Install the engine to the transmission. Transmission Replacement (LIH)
- Position the powertrain and support table under the vehicle.
- Raise the support table to move the powertrain into it's installed position.
- Transmission Mount - Install - Transmission Mount Replacement
- Engine Mount - Install - Engine Mount Replacement
- Propulsion System Lift Table - Remove - Propulsion System Lift Table
Remove the left drive shaft (1) from the hoist (3).
- Left Front Wheel Drive Shaft (1) @ Transmission - Connect - Front Wheel Drive Half Shaft Replacement - Left Side
Remove the right drive shaft (2) from the hoist (1).
- Right Front Wheel Drive Shaft (2) @ Transmission - Connect - Front Wheel Drive Half Shaft Replacement - Right Side (FWD)
Transmission Mount Strut - Install - Transmission Mount Strut Replacement
Drivetrain and Front Suspension Cradle - Install - Drivetrain and Front Suspension Cradle Removal and Installation (FWD)
- Radiator - Install
Exhaust Front Muffler - Install - Exhaust Front Muffler Replacement (FWD)
Air Conditioning Compressor - Install - Air Conditioning Compressor Replacement (LIH)
- Radiator Outlet Hose - Install - Radiator Outlet Hose Replacement (LIH)
Charge Air Cooler Outlet Air Hose - Install - Charge Air Cooler Outlet Air Hose Replacement
- Transmission Fluid Cooler Outlet Pipe - Install - Transmission Fluid Cooler Outlet Pipe Replacement (LIH)
- Transmission Fluid Cooler Inlet Pipe - Install - Transmission Fluid Cooler Inlet Pipe Replacement (LIH)
Automatic Transmission Range Selector Lever Cable (4) @ Range Selector Lever Cable Lever - Install
- Automatic Transmission Range Selector Lever Cable Bolt (1) - Install and tighten 9 N.m (80 lb in)
- Depress the cable adjustment retainer (3) locking the retainer completely.
- Slide the retainer lock (2) rearward to cover the cable adjustment retainer (3).
- Range Selector Lever Cable - Adjust - Range Selector Lever Cable Adjustment
Heater Inlet Hose - Install - Heater Inlet Hose Replacement (LIH)
Heater Outlet Hose - Install - Heater Outlet Hose Replacement (LIH)
Engine Wiring Harness Connector (5) - Connect
- Transmission Control Module Wiring Harness (4) - Connect
- Ground Cable (2) - Install
- Ground Nut (1) - Install
Radiator Inlet Hose - Install - Radiator Inlet Hose Replacement (LIH)
Engine Wiring Harness (2) - Install
Engine Wiring Harness Junction Block - Install - Engine Wiring Harness Junction Block Replacement
- Battery Tray - Install - Battery Tray Replacement
- Charge Air Cooler Inlet Air Hose - Install - Charge Air Cooler Inlet Air Hose Replacement
- Evaporative Emission Pipe - Install - Evaporative Emission Pipe Replacement (Fuel Tank Side) , or Evaporative Emission Pipe Replacement (Underbody Side)
- Evaporative Emission Canister Purge Tube - Install - Evaporative Emission Canister Purge Tube Replacement
Fuel Feed Front Pipe - Install - Fuel Feed Front Pipe Replacement
Air Cleaner Outlet Rear Duct - Install - Air Cleaner Outlet Rear Duct Replacement
Air Cleaner Assembly - Install - Air Cleaner Assembly Replacement
Radiator Surge Tank Outlet Hose - Install - Radiator Surge Tank Outlet Hose Replacement (LIH)
Engine Coolant Air Bleed Hose - Install - Engine Coolant Air Bleed Hose Replacement
Engine Control Module Bracket - Install - Engine Control Module Bracket Replacement
- Connect the battery negative cable. Battery Negative Cable Disconnection and Connection
- Recharge the refrigerant. Refrigerant Recovery and Recharging
- Fill the engine oil to the proper level with NEW engine oil. Engine Oil and Oil Filter Replacement
- Fill the cooling system. Cooling System Draining and Filling (GE-47716) , or Cooling System Draining and Filling (Static)
- Perform the crankshaft position variation learn. Crankshaft Position Variation Learn
- If NEW engine has been installed, perform timing belt life reset. Timing Belt Life Reset