Additional Symptoms Tests

Detonation/Spark Knock:

• Test the engine for an overheating condition. Refer to Symptoms - Engine Cooling .
• Inspect for excessive carbon buildup in the combustion chambers. Clean the chambers with Top Engine Cleaner, if necessary. Follow the instructions on the can.
• If there are no engine mechanical faults, fill the fuel tank with a known high quality fuel that meets the vehicle minimum octane requirements.

ECM Commanded Reduced Engine Power 

Under certain conditions the engine control module may limit engine power by reducing engine torque and, for some vehicles, fuel pressure as well. For most, but not all of the conditions, the engine control module will illuminate the reduced engine power lamp on the instrument cluster. If equipped with the driver information center feature, a reduced engine power message may be displayed as well. A DTC may not be set.

A repair may not be necessary. Observe the scan tool Reduced Engine Power History parameter or refer to K20 Engine Control Module: Scan Tool Information to determine the reason for the reduced engine power event.

Verify or inspect for the following:

• Vehicle being operated at sustained high engine speeds, or, towing heavy loads up an incline for an extended period of time, which may cause the engine oil or coolant to overheat. Inspect the airflow passageways in front of the engine for obstructions and clear away any debris or foreign material that is found. If no obstructions are found, review approved driving habits with the customer. The customer may need to operate the vehicle at a higher engine speed to improve cooling system performance, or, at a slower engine speed to reduce engine load.
• A cooling fan condition which may cause the ECM to reduce engine power. Refer to Cooling Fan Description and Operation , or Cooling System Description and Operation (LSY) to verify correct operation of the cooling fan.
• Fuel temperature out of range too high.
• High pressure fuel system condition. Refer to Fuel System Diagnosis , and Fuel System Description to verify high pressure fuel system operation.
• Reduced engine power due to OnStar® remote command. Verify the vehicle is not in the OnStar® initiated Stolen Vehicle Slowdown mode.
• Turbocharger boost pressure out of range, if equipped. Refer to DTC P0299 .
• Intake air temperature out of range too high. Engine running, observe the scan tool IAT sensor parameter. The readings should be between -40° C and +149° C (-40° F and +300° F. Refer to DTC P0097-P0099, P00F4-P00F6, or P0112-P0114 for additional information.
• If equipped with manual transmission, excessively hot manual transmission fluid. Under severe operating conditions the fluid may become overheated, which may result in ECM commanded reduced engine power. Allow the transmission and fluid to cool down. Review the maintenance recommendation in the owner's manual to determine if the transmission fluid is due to be serviced.
• If equipped with automatic transmission, an incorrect learned brake pedal position (BPP) sensor. Verify the following actions have not occurred:
  • An engine control module has been replaced
  • A BPP sensor that has been replaced
  • A BPP sensor is misaligned or incorrectly installed

    If any of the above actions have occurred, the Brake Pedal Position Sensor Calibration procedure must be performed.

Fuel Odor

• Inspect for leaking, damaged, or deteriorated fuel lines and components.
• Inspect for a saturated EVAP canister. Refer to Evaporative Emission Control System Description .
• Inspect for a condition with the internal components of the fuel tank assembly. Refer to Fuel System Description .

Hard Start

• Observe the scan tool Throttle Body Idle Airflow Compensation parameter. A value greater than 90% may indicate an excessive accumulation of deposits in the throttle bore. Inspect the throttle body and bore and clean, if necessary. Refer to Throttle Body Cleaning .
• Test the engine coolant temperature (ECT) sensor. Compare the ECT sensor value to the intake air temperature (IAT) sensor value on a cold engine. The ECT and IAT sensor values should be within approximately 3°C (5°F). If the ECT sensor is out of range with the IAT sensor, test the resistance of the ECT sensor. Refer to Temperature Versus Resistance - Engine Coolant Temperature Sensor , or Temperature Versus Resistance - Intake Air Temperature Sensor for resistance specifications. Replace the ECT sensor if the resistance is not within specification. If the sensor is within the specification, test the ECT circuits for a high resistance.
• Verify that the fuel system operates correctly and provides adequate pressure for engine start-up The fuel pump should turn ON for 2 s when the ignition is turned ON. Refer to Fuel System Diagnosis , and Fuel System Description for fuel pressure specifications and additional information.

Hesitation, Sag, Stumble

• Test the fuel pressure. Refer to Fuel System Diagnosis .
• Test the manifold absolute pressure (MAP) sensor. Refer to DTC P0106, P0107, or P0108 .
• Test the generator. Refer to Symptoms - Engine Electrical . Repair the charging system if the generator output voltage is less than 9 V or more than 16 V.

Lack of Power, Sluggishness, or Sponginess (Turbo)

• Inspect the engine electrical system for incorrect operation. Refer to Symptoms - Engine Electrical .
• Verify that each injector harness is connected to the correct injector.
• Inspect the MAF sensor for obstruction, contamination, and damage. Refer to Mass Airflow Sensor Replacement .
• If equipped with a Supplemental Transmission Auto Shift, verify that the brake sensor is not stuck in the applied position. The Enhanced Electronic Pedal Override functionality in the ECM reduces the driver torque request if the accelerator pedal and the brake pedal are applied simultaneously
• Verify the correct operation of the turbocharger system. Perform the following:
  • Inspect the turbocharger moving components for looseness, binding, wear and damage.
  • Verify that the turbocharger air inlet ducts and outlet ducts are tightly sealed and that the air passages are not obstructed. Engine running, use a smoke generating device or a solution of dish soap and water in a spray bottle to pinpoint any air leaks.
  • Inspect the turbocharger system for external fluid leaks. Inspect the gaskets and sealing surfaces and look for cracks in the turbocharger components.
  • Inspect for excessive turbocharger system noise. Operate the vehicle at various acceleration modes and compare the turbocharger noise to the noise made by a known good system.

Lack of Power, Sluggishness, or Sponginess (Except Turbo)

• Inspect the engine electrical system for incorrect operation. Refer to Symptoms - Engine Electrical .
• Verify that each injector harness is connected to the correct injector.
• Inspect the MAF sensor for obstruction, contamination, and damage. Refer to Mass Airflow Sensor Replacement .

Poor Fuel Economy

• Observe the scan tool Throttle Body Idle Airflow Compensation parameter. A value greater than 90% may indicate an excessive accumulation of deposits in the throttle bore. Inspect the throttle body and bore and clean, if necessary. Refer to Throttle Body Cleaning .
• Inspect for heavy loads being carried or towed
• Inspect for acceleration rate too much or too often
• Inspect for incorrect operation of the speedometer.
• Inspect the brake system for brake drag.

Rough, Unstable, or Incorrect Idle and Stalling

• An excessively high idle may be due to the floor mat interfering with the accelerator pedal. With this condition present, it may not be possible to shift the transmission into gear. Inspect the accelerator pedal for binding and verify that the floor mat is not interfering with the accelerator pedal movement.
• Engine idle speed be unstable or the engine may stall if the ECM has learned an incorrect idle/airflow compensation value. A DTC may also set. Observe the scan tool Throttle Body Idle Airflow Compensation parameter. A value greater than 90% may indicate an excessive accumulation of deposits in the throttle bore. If the throttle body needs cleaning, refer to Throttle Body Cleaning .

  The actions listed below may also cause the ECM to learn an incorrect idle value:

  • The ECM has been replaced
  • The throttle body has been replaced
  • The throttle body has been cleaned but the idle learn procedure was not performed after completing the cleaning
  • The air induction system was leaking, allowing non-metered air to enter the combustion chamber. The leak was repaired, but the idle learn procedure was not performed after repairing the leak.

    If any of the actions listed above have occurred, the Throttle Body Idle Air Flow Compensation Reset procedure must be performed.

• Inspect the engine mounts for looseness, damage, and wear.
• Inspect the intake and exhaust manifolds for casting flash.
• Inspect engine coolant for a slushy or frozen condition. Refer to Cooling System Draining and Filling (Static LSY) , or Cooling System Draining and Filling (GE 47716 LSY) .

Surges/Chuggles

• Verify that each injector harness is connected to the correct injector.
• Inspect for slow responding Heated Oxygen Sensors (HO2S). The HO2S should respond quickly to a change in throttle position. If the HO2S do not respond to different throttle positions, inspect for contamination from fuel, silicon, or the incorrect use of room temperature vulcanizing sealant. The sensors may have a white powdery coating and result in a high, but false, signal voltage, which gives a rich exhaust indication. The ECM reduces the amount of fuel delivered to the engine, causing a driveability condition.