LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2020 >> Malibu LS >> Repair and Diagnosis >> External Pages >> Different car >> Section 83 (Data Communication System - Diagnostic Information And Procedures (2 Of 2)) >> Diagnostic Information and Procedures >> DTC U1876 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2019 Chevrolet Malibu. However, it is still accessible from the selected car via links, so may be relevant.
WARNING:

Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal Protection Equipment (PPE) and proper procedures must be followed.

The High Voltage Disabling procedure includes the following steps:

  • Identify how to disable high voltage.
  • Identify how to test for the presence of high voltage.
  • Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures must be followed.

Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:

  • Safety glasses with appropriate side shields when within 15 meters (50 feet) of the vehicle, either indoors or outdoors.
  • Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
    • Visually and functionally inspect the gloves before use.
    • Wear the Insulation gloves with leather protectors at all times when working with the high voltage battery assembly, whether the system is energized or not.

Failure to follow the procedures may result in serious injury or death.

NOTE:

Use the Wiring Schematics and connector end views to identify the device's ground, B+, ignition, accessory wakeup serial data 2, and serial data circuit terminals.

  1. Ignition/Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. Disconnect the harness connectors at the K20 Engine Control Module. It may take up to 10 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between each ground circuit terminal and ground.
    • If 10 Ω or greater 
    1. Ignition/Vehicle OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Ignition ON/Vehicle in Service Mode.
  4. If equipped, verify a test lamp illuminates between each B+ circuit terminal and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K20 Engine Control Module.
    • Go to next step: If the test lamp illuminates 
  5. If equipped, verify a test lamp illuminates between each ignition circuit terminal and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K20 Engine Control Module.
    • Go to next step: If the test lamp illuminates 
  6. If equipped, verify a test lamp illuminates between the accessory wakeup serial data 2 circuit terminal and ground.
    • If the test lamp does not illuminate 
    1. Disable the high voltage system. Refer to High Voltage Disabling .
    2. Ignition/Vehicle OFF, remove the test lamp, disconnect the harness connectors at the K114B Hybrid/EV Powertrain Control Module 2.
    3. Test for less than 2 Ω in the accessory wakeup serial data 2 circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K114B Hybrid/EV Powertrain Control Module 2.
    • Go to next step: If the test lamp illuminates 
  7. Ignition/Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. Disconnect the X1 harness connector at the T6 Power Inverter Module. It may take up to 10 min for all vehicle systems to power down.
  8. Test for less than 2 Ω in each serial data circuits end to end between the K20 Engine Control Module and the T6 Power Inverter Module.
    • If 2 Ω or greater 

      Repair the open/high resistance in the serial data circuit.

    • Go to next step: If less than 2 Ω 
  9. Replace the K20 Engine Control Module.
scientia non olet · About LEMON Manuals