LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2020 >> Express 2500 LS, 6.0L Eng VIN G >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 21 (Engine Controls And Fuel - 4.3L (LV1) - Diagnostic Information And Procedures (2 Of 2)) >> Diagnostic Information and Procedures >> DTC P2147, P2148, P2150, P2151, P2153, P2154, P2156, P2157, P216B, P216C, P216E, or P216F >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different variant/trim than selected.
  1. Ignition/Vehicle - Off
  2. Disconnect the appropriate electrical connector : Q17 Fuel Injector
  3. Ignition - On / Vehicle - In Service Mode
  4. Test for 5 to 6 V between the test points : Control circuit terminal 1 & Ground
    • If less than 5 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector : X3 @ K20 Engine Control Module
    3. Test for infinite resistance between the test points : Control circuit terminal 1 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step : If infinite resistance
    4. Test for less than 2 ohms between the test points : Control circuit terminal 1 @ Component harness &
      • { Q17A Fuel Injector 1 } Terminal 72 @ Control module harness
      • { Q17B Fuel Injector 2 } Terminal 71 @ Control module harness
      • { Q17C Fuel Injector 3 } Terminal 67 @ Control module harness
      • { Q17D Fuel Injector 4 } Terminal 66 @ Control module harness
      • { Q17E Fuel Injector 5 } Terminal 70 @ Control module harness
      • { Q17F Fuel Injector 6 } Terminal 68 @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component : K20 Engine Control Module
    • If greater than 6 V 
    1. Ignition/Vehicle - Off
    2. Test for infinite resistance between the test points : Control circuit terminal 1 & Control circuit terminal 2 @ Component harness
      • If less than infinite resistance - Repair the short between the circuits.
      • Go to next step : If infinite resistance
    3. Disconnect the electrical connector : X3 @ K20 Engine Control Module
    4. Ignition - On / Vehicle - In Service Mode
    5. Test for less than 1 V between the test points : Control circuit terminal 1 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component : K20 Engine Control Module
    • Go to next step : If between 5 and 6 V 
  5. Clear the DTCs.
  6. Ignition/Vehicle - Off
  7. Connect a test lamp between the test points : Control circuit terminal 1 & Control circuit terminal 2 @ Q17 Fuel Injector - Component harness
  8. Engine - Cranking
  9. Verify the test lamp flashes - For 2 s
    • If the test lamp does not flash 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the electrical connector : X3 @ K20 Engine Control Module
    3. Test for infinite resistance between the test points : Control circuit terminal 2 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step : If infinite resistance
    4. Test for less than 2 ohms between the test points : Control circuit terminal 2 @ Component harness &
      • { Q17A Fuel Injector 1 } Terminal 52 @ Control module harness
      • { Q17B Fuel Injector 2 } Terminal 71 @ Control module harness
      • { Q17C Fuel Injector 3 } Terminal 47 @ Control module harness
      • { Q17D Fuel Injector 4 } Terminal 46 @ Control module harness
      • { Q17E Fuel Injector 5 } Terminal 50 @ Control module harness
      • { Q17F Fuel Injector 6 } Terminal 48 @ Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • Go to next step : If less than 2 ohms
    5. Ignition - On / Vehicle - In Service Mode
    6. Test for less than 1 V between the test points : Control circuit terminal 2 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component : K20 Engine Control Module
    • Go to next step : If the test lamp flashes 
  10. Test or replace the component : Q17 Fuel Injector
scientia non olet · About LEMON Manuals