Circuit/System Verification
WARNING: This page is about a different car, the 2019 GMC Savana 3500, 2019 GMC Savana 2500, 2019 Chevrolet Express 3500, and 2019 Chevrolet Express 2500. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
This diagnostic assumes the following:
- The battery is completely charged.
- The engine cranking speed is acceptable.
- There is adequate fuel in the fuel tank.
- Crank the engine for up to 15 seconds.
- Verify that DTC P0117, P0118, P0122, P0123, P0201 - P0208, P0222, P0223, P0300 - P0308, P0335, P0336, P0351 - P0358, P0562, P0563, P0601 - P0604, P0606, P0607, P062F, P0633, P0685, P0690, P1631, P1682, or P2610 is not set.
- If any of the DTCs are set
Refer to Diagnostic Trouble Code (DTC) List - Vehicle .
- Go to next step: If none of the DTCs are set
- If any of the DTCs are set
- Ignition ON
- Verify the security indicator on the instrument cluster illuminates momentarily.
- If the security indicator stays ON or is flashing
Review the Diagnostic Trouble Code (DTC) List - Vehicle , for Immobilizer system DTCs. For additional information, refer to Immobilizer Description and Operation .
- Go to next step: If the security indicator does not stay ON and is not flashing
- If the security indicator stays ON or is flashing
- Verify the scan tool Engine Speed parameter displays greater than 0 RPM while cranking the engine.
- If 0 RPM
Refer to DTC P0335 or P0336 .
- Go to next step: If greater than 0 RPM
- If 0 RPM
- Ignition OFF, disconnect a spark plug wire from one of the spark plugs.
- Connect the EL 26792 HEI Spark Tester between the spark plug boot and ground.
- Perform the spark test on at least one cylinder from each engine bank.
- An erratic or weak spark is considered a no spark condition.
- Verify the spark tester sparks while cranking the engine.
- If the spark tester does not spark
Refer to Electronic Ignition System Diagnosis .
- Go to next step: If the spark tester sparks
- If the spark tester does not spark
- Ignition OFF, install the CH-48027 Digital Pressure Gauge. Refer to Fuel Pressure Gauge Installation and Removal .
- If the engine is too hot, high fuel pressure readings may result due to hot soak fuel boiling. Allow the engine coolant temperature to cool to less than 60° C (150° F) before attempting to verify fuel pressure.
- The fuel pump may need to be commanded ON a few times in order to obtain the highest possible fuel pressure.
- Additional DTCs may set when using the fuel pump output control.
- Ignition ON.
- Command the Fuel Pump Enable ON several times with a scan tool.
- Verify the fuel pressure is between 345 - 690 kPa (50 - 100 psi) with the fuel pump running.
- If not within the specified range
Refer to Fuel System Diagnosis (Without FPCM) , or Fuel System Diagnosis (FPCM) .
- Go to next step: If within the specified range
- If not within the specified range
- Verify that the fuel pressure, after the fuel pump turns OFF, stabilizes between 500 - 599 kPa (72 - 87 psi) and does not decrease greater than 34 kPa (5 psi) in 1 min.
- If not within the specified range
Refer to Fuel System Diagnosis (Without FPCM) , or Fuel System Diagnosis (FPCM) .
- Go to next step: If within the specified range
- If not within the specified range
- Verify the conditions listed below do not exist:
- Collapsed air intake duct to the throttle body
- Restricted air filter element
- Spark plugs for being fouled
- A skewed manifold absolute pressure (MAP) sensor - Refer to DTC P0106 .
- A skewed engine coolant temperature (ECT) sensor - Refer to DTC P0116-P0119 .
- Exhaust system restricted - Refer to Restricted Exhaust .
- Fuel contamination - Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
- Engine mechanical condition - Refer to Symptoms - Engine Mechanical , or Engine Compression Test .
- If a condition exists
Repair as necessary.
- Go to next step: If no condition exists
- All OK.
NOTE:
NOTE: