LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2020 >> Camaro SS, 2D Coupe, Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Exterior Lights >> Lighting System - Diagnostic Information And Procedures (B053A-B3949) >> Diagnostic Information and Procedures >> DTC B1395 >> Circuit/System Testing

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the S36 Instrument Panel Dimmer Switch, ignition ON.
  2. Test for B+ between the B+ reference circuit terminal 6 and ground.
    • If less than B+ 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the B+ reference circuit terminal 6 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the B+ reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If B+ 
  3. Verify a test lamp does not illuminate between B+ and the signal circuit terminal 2.
    • If the test lamp illuminates 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit terminal 2 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • Go to next step: If the test lamp does not illuminate 
  4. Test for B+ between the B+ reference circuit terminal 6 and the signal circuit terminal 2.
    • If less than B+ 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 2 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If B+ 
  5. Test for B+ between the B+ reference circuit terminal 6 and the low reference circuit terminal 1.
    • If less than B+ 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the low reference circuit terminal 1 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    3. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If B+ 
  6. Verify a test lamp does not illuminate between the B+ reference circuit terminal 6 and ground.
    • If the test lamp illuminates 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the B+ reference circuit terminal 6 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If the test lamp does not illuminate 
  7. Test or replace the S36 Instrument Panel Dimmer Switch.
scientia non olet · About LEMON Manuals