LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2018 >> Traverse LT, FWD >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine Mechanical - 3.6L (LFY) - Repair Instructions - Off Vehicle >> Repair Instructions - Off Vehicle >> Engine Block Assemble

Engine Block Assemble

  1. GM902736

    Install the cylinder block-to-cylinder head alignment dowels.

  2. GM902730

    Install the NEW front oil gallery expansion plug.

  3. Ensure the NEW front oil gallery expansion plug is installed to the proper depth.
  4. GM902737

    Install the cylinder block-to-transmission alignment dowels.

  5. GM902733

    Ensure proper use of room temperature vulcanizing (RTV) sealant. Use of Room Temperature Vulcanizing (RTV) and Anaerobic Sealant

    Apply the RTV sealant on the NEW coolant expansion plugs. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended sealant.

  6. Install the NEW coolant expansion plugs.
  7. Ensure the NEW coolant expansion plugs are installed to the proper depth.
  8. GM1327926

    Apply thread sealant on the threads of the M20 left side oil gallery threaded plug. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended sealant.

    9. CAUTION:

    Refer to Fastener Caution .

  9. Install the M20 left side oil gallery threaded plug and tighten to 75 N.m (55 lb ft).
  10. GM1327925

    Apply thread sealant on the threads of the M14 left side coolant drain threaded plug. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended sealant.

  11. Install the M14 left side coolant drain threaded plug and tighten to 50 N.m (37 lb ft).
  12. GM1327924

    Apply thread sealant on the threads of the M14 rear oil gallery threaded plug. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended sealant.

  13. Install the M14 rear oil gallery threaded plug and tighten to 50 N.m (37 lb ft).
  14. GM1327923

    Apply thread sealant on the threads of the M14 right side coolant drain threaded plug. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended sealant.

  15. Install the M14 right side coolant drain threaded plug and tighten to 50 N.m (37 lb ft).
  16. GM1327922

    Apply thread sealant on the threads of the M14 right side oil gallery threaded plug. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended sealant.

  17. Install the M14 right side oil gallery threaded plug and tighten to 50 N.m (37 lb ft).
  18. GM902740

    Install the cylinder block-to-oil pan alignment dowels.

  19. GM902732

    Install the NEW right front oil pan rail oil gallery expansion plug.

  20. Ensure the NEW right front oil pan rail oil gallery expansion plug is installed to the proper depth.
  21. GM1866877

    Install the oil jets.

  22. Install the oil jet bolts and tighten to 10 N.m (89 lb in).
  23. GM1930269

    Install the NEW crankshaft position sensor O-ring, if damaged.

  24. GM1930246

    Install the crankshaft position sensor.

  25. Install the crankshaft position sensor bolt and tighten to 10 N.m (89 lb in).
  26. GM1930214

    Install the left knock sensor to the cylinder block, as shown.

  27. Install the left knock sensor bolt and tighten to 25 N.m (18 lb ft).
  28. Ensure proper sensor orientation.
  29. GM1930195

    Install the right knock sensor to the cylinder block, as shown.

  30. Install the right knock sensor bolt and tighten to 25 N.m (18 lb ft).
  31. Ensure proper sensor orientation.
  32. GM1930194

    Install the block heater cartridge, if equipped.

  33. GM2296303

    Install the engine front cover studs (1) and tighten to 15 N.m (11 lb ft).

scientia non olet · About LEMON Manuals