LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2018 >> Traverse LS, 4WD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Headlights >> Lighting System - Diagnostic Information And Procedures >> Diagnostic Information and Procedures >> DTC B3881 or B3882 >> Circuit/System Testing

Circuit/System Testing

DTC B3881

  1. Ignition OFF, exterior lamps OFF, disconnect the harness connector at the E5AM Stop/Turn Signal Lamp - Left. It may take up to 2 min for all vehicle systems to power down
  2. Test for less than 5 Ω between the ground circuit at the socket terminal and ground.
    • If 5 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 5 Ω 
  3. Connect a test lamp between the control circuit at the socket terminal and ground, ignition ON.
  4. Verify the test lamp turns ON and OFF when commanding the Left Rear Turn Signal/Stop Lamp ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If the test lamp turns ON and OFF 
  5. Test or replace the E5AM Stop/Turn Signal Lamp - Left.

DTC B3882

  1. Ignition OFF, exterior lamps OFF, disconnect the harness connector at the E5AN Stop/Turn Signal Lamp - Right. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 5 Ω between the ground circuit at the socket terminal and ground.
    • If 5 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 5 Ω 
  3. Connect a test lamp between the control circuit at the socket terminal and ground, ignition ON.
  4. Verify the test lamp turns ON and OFF when commanding the Right Rear Turn Signal/Stop Lamp ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X5 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X5 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If the test lamp turns ON and OFF 
  5. Test or replace the E5AN Stop/Turn Signal Lamp - Right.
scientia non olet · About LEMON Manuals