Test 2

WARNING: This page is about a different car, the 2017 Chevrolet Spark. However, it is still accessible from the selected car via links, so may be relevant.

Ignition/Vehicle - Off
Disconnect the electrical connector: S79P Window Switch - Passenger
Connect a test lamp between the test points: Control circuit terminal 3 & Control circuit terminal 6
Ignition - On / Vehicle - In Service Mode
Operate the component: Right Front Window Switch @ S79D Window Switch - Driver
Verify the test lamp state:
- Not Pressed=Test lamp Off
- Pulled - Up=Test lamp On
- Pressed - Down=Test lamp On
- If not the specified state
1. Ignition/Vehicle - Off & Remove - Test lamp
2. Disconnect the electrical connector: S79D Window Switch - Driver
3. Ignition - On / Vehicle - In Service Mode
4. Test for less than 1 V between the test points:
  - Control circuit terminal 3 @ Component harness & Ground
  - Control circuit terminal 6 @ Component harness & Ground
  - If 1 V or greater - Repair the short to voltage on the circuit.
  - If less than 1 V
1. Ignition/Vehicle - Off
2. Test for infinite resistance between the test points:
  - Control circuit terminal 3 @ Component harness & Ground
  - Control circuit terminal 6 @ Component harness & Ground
  - If less than infinite resistance - Repair the short to ground on the circuit.
  - If less than infinite resistance
1. Test for less than 2 Ω between the test points:
  - {RHD} Control circuit terminal 6 @ Component harness & Terminal 7 @ Component harness
  - {RHD} Control circuit terminal 3 @ Component harness & Terminal 9 @ Component harness
  - {LHD} Control circuit terminal 6 @ Component harness & Terminal 13 @ Component harness
  - {LHD} Control circuit terminal 3 @ Component harness & Terminal 14 @ Component harness
    - If 2 Ω or greater - Repair the open/high resistance in the circuit.
    - If less than 2 Ω - Replace the component: S79D Window Switch - Driver
- If the specified state
Ignition/Vehicle - Off
Connect the electrical connector: S79P Window Switch - Passenger
Disconnect the electrical connector: M74P Window Motor - Passenger
Connect a test lamp between the test points: Control circuit terminal 1 & Control circuit terminal 2
Ignition - On / Vehicle - In Service Mode
Operate the component: S79P Window Switch - Passenger
Verify the test lamp state:
- Not Pressed=Test lamp Off
- Pulled - Up=Test lamp On
- Pressed - Down=Test lamp On
- If not the specified state
1. Ignition/Vehicle - Off & Remove - Test lamp
2. Disconnect the electrical connector: S79P Window Switch - Passenger
3. Ignition - On / Vehicle - In Service Mode
4. Test for less than 1 V between the test points:
  - Control circuit terminal 1 @ Component harness & Ground
  - Control circuit terminal 2 @ Component harness & Ground
  - If 1 V or greater - Repair the short to voltage on the circuit.
  - If less than 1 V
1. Ignition/Vehicle - Off
2. Test for infinite resistance between the test points:
  - Control circuit terminal 1 @ Component harness & Ground
  - Control circuit terminal 2 @ Component harness & Ground
  - If less than infinite resistance - Repair the short to ground on the circuit.
  - If less than infinite resistance
1. Test for less than 2 Ω between the test points:
  - Control circuit terminal 1 @ Component harness & Terminal 4 @ Component harness
  - Control circuit terminal 2 @ Component harness & Terminal 1 @ Component harness
    - If 2 Ω or greater - Repair the open/high resistance in the circuit.
    - If less than 2 Ω - Replace the component: S79P Window Switch - Passenger
- If the specified state
Test or replace the component: M74P Window Motor - Passenger