LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2018 >> Spark LT, Automatic CVT Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 44 (Engine Mechanical - 1.4L (LV7) - Diagnostic Information And Procedures) >> Diagnostic Information and Procedures >> DTC P06DA-P06DE: Engine Oil Pressure Control Solenoid Valve >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2017 Chevrolet Spark. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the appropriate electrical connector: Inline Harness Connector
  3. Ignition - On / Vehicle - In Service Mode
  4. Verify a test lamp turns On between the test points: Ignition circuit terminal 5 & Ground
    NOTE: Testing for steps 4 to 9 is performed on the control module K20 side of the inline harness connector.
    • If the test lamp does not turn On and the circuit fuse is OK 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Test for less than 2 Ω between the test points: Ignition circuit terminal 5 & Fuse
      • If 2 Ω or greater - Repair the open/high resistance in the circuit.
      • If less than 2 Ω - Verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not turn On and the circuit fuse is open 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Test for infinite resistance between the test points: Ignition circuit terminal 5 & Ground
      NOTE: The ignition circuit supplies voltage to other components. Test all circuits for a short to ground or test all components for being shorted.
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Refer to Step 10
    • If the test lamp turns On 
  5. Verify a test lamp does not turn On between the test points: Control circuit terminal 4 & B+
    • If the test lamp turns On 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Test for infinite resistance between the test points: Inline Harness Connector Control circuit terminal 4 & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: K20 Engine Control Module
    • If the test lamp does not turn On 
  6. Remove - Test Lamp
  7. Perform the scan tool control function: Engine Oil Pressure Control Solenoid Valve - Low Pressure

    Verify the scan tool parameter: Engine Oil Pressure Control Solenoid Valve Control Circuit High Voltage Test Status =OKorNot Run

    • If not the specified state 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Test for less than 1 V between the test points: Inline Harness Connector Control circuit terminal 4 & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K20 Engine Control Module
    • If the specified state 
  8. Connect a 3 A fused jumper wire between the test points: Control circuit terminal 4 & Ignition circuit terminal 5
  9. Perform the scan tool control function: Engine Oil Pressure Control Solenoid Valve - Low Pressure

    Verify the scan tool parameter: Engine Oil Pressure Control Solenoid Valve Control Circuit High Voltage Test Status =Malfunction

    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Test for less than 2 Ω between the test points: Inline Harness Connector Control circuit terminal 4 & The other end of the circuit
      • If 2 Ω or greater - Repair the open/high resistance in the circuit.
      • If less than 2 Ω - Replace the component: K20 Engine Control Module
    • If the specified state 
  10. Test for 10 to 30 Ω between the test points: Control circuit terminal 4 & Ignition circuit terminal 5
    NOTE: Testing for steps 10 to 12 is performed on the component side of the inline harness connector: Q44 Engine Oil Pressure Control Solenoid Valve
    • If not between 10 to 30 Ω 
    1. Disconnect the electrical connector: Q44 Engine Oil Pressure Control Solenoid Valve
    2. Test for less than 2 Ω between the test points:
      • Ignition circuit terminal 5 & The other end of the circuit
      • Control circuit terminal 4 & The other end of the circuit
      • If 2 Ω or greater - Repair the open/high resistance in the circuit.
      • If less than 2 Ω - Test or replace the component: Q44 Engine Oil Pressure Control Solenoid Valve
    • If between 10 and 30 Ω 
  11. Test for infinite resistance between the test points:
    • Ignition circuit terminal 5 & Ground
    • Control circuit terminal 4 & Ground
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • If infinite resistance 
  12. Test for less than 1 V between the test points:
    • Ignition circuit terminal 5 & Ground
    • Control circuit terminal 4 & Ground
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • If less than 1 V 
  13. Test or replace the component: Q44 Engine Oil Pressure Control Solenoid Valve
scientia non olet · About LEMON Manuals