A11 Radio: Scan Tool Information
WARNING: This page is about a different car, the 2019 Buick Cascada, 2018 Buick Cascada, and 2017 Buick Cascada. However, it is still accessible from the selected car via links, so may be relevant.
Radio Scan Tool Data Parameters
| Parameter | Expected Value | Definition |
|---|---|---|
| Operating Conditions: Ignition ON | ||
| Antenna Module | Enabled | The scan tool displays Enabled or Disabled. This indicates if the system uses an antenna module and the output status between the radio and the antenna module. |
| Auxiliary Audio Input | Present | The scan tool displays Present or Not Present. This parameter displays active when an auxiliary input is connected. |
| Battery Voltage | Varies | The scan tool displays volts. This is the voltage at the input to the radio. |
| Digital Radio Receiver | Present | The scan tool displays Present or Not Present. This is the state of the Digital Audio Broadcast. |
| Phone Signal | Present | The scan tool displays Present or Not Present. This parameter will display wether this system uses discrete a phone arbitration or not. |
| Power Mode | Run | The scan tool displays Off, Accessory, Run or Crank Request. This is the power mode radio. |
| Rear Seat Audio | Not Present | The scan tool displays Present or Not Present. This parameter displays Present if the system detects a rear seat audio module. |
| Radio Signal Strength | Varies | This displays the signal strength in dB. This is the signal strength of the radio signal. |
| Theft Lock Armed | Learned VIN | The scan tool displays Learned VIN or No VIN. This is the state of the VIN programming in the radio. |
| Radio Theft Lock Status | Inactive | The scan tool displays Active or Inactive. This is the state of the theft lock system. |
| Valet Mode Status | Inactive | The scan tool displays Active or Inactive. This is the state of the valet mode. |
| Video Display 1 | Inactive | The scan tool displays Active or Inactive. When the rear video display 1 is ON, the scan tool will display Active. |
| Video Display 2 | Inactive | The scan tool displays Active or Inactive. When the rear video display 2 is ON, the scan tool will display Active. |
| End Model Part Number | Varies | The scan tool displays the end model part number. |
| Boot Software Part Number | Varies | The scan tool displays the boot software ID number. |
| Calibration Part Number 1 | Varies | The scan tool displays the software module ID 1. |
| Calibration Part Number 2 | Varies | The scan tool displays the software module ID 2. |
| Calibration Part Number 3 | Varies | The scan tool displays the software module ID 3. |
| Calibration Part Number 4 | Varies | The scan tool displays the software module ID 4. |
| Calibration Part Number 5 | Varies | The scan tool displays the software module ID 5. |
| Calibration Part Number 6 | Varies | The scan tool displays the software module ID 6. |
| Calibration Part Number 7 | Varies | The scan tool displays the software module ID 7. |
| Calibration Part Number 8 | Varies | The scan tool displays the software module ID 8. |
| Calibration Part Number 9 | Varies | The scan tool displays the software module ID 9. |
| Calibration Part Number 10 | Varies | The scan tool displays the software module ID 10. |
| Calibration Part Number 11 | Varies | The scan tool displays the software module ID 11. |
| Calibration Part Number 12 | Varies | The scan tool displays the software module ID 12. |
| Calibration Part Number 13 | Varies | The scan tool displays the software module ID 13. |
| Calibration Part Number 14 | Varies | The scan tool displays the software module ID 14. |
| Calibration Part Number 15 | Varies | The scan tool displays the software module ID 15. |
| Calibration Part Number 16 | Varies | The scan tool displays the software module ID 16. |
| Vin Digits 2-17 | Varies | The scan tool displays the vin digits 2-17. |
| Digital Radio Receiver ID | Varies | The scan tool displays the Digital Audio Broadcast receiver ID. |
| DVD Region Code | Varies | The scan tool displays the DVD region code. |
| DVD Region Code Changes Remaining | Varies | The scan tool displays the number DVD region code changes remaining. |
Radio Scan Tool Output Controls
| Scan Tool Output Control | Description |
|---|---|
| Left Front Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Left Rear Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Right Front Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Right Rear Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Center Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Subwoofer Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Eject | This output is a reset command to eject the disc. |
| Info Display/Infotainment Faceplate Reset | This output is a reset command to reset the radio display. |
| Info Display/Infotainment Faceplate Wakeup | This output commands a wakeup at the display and the faceplate controls. |
| Clear Hard Disc Drive | This output commands a HDD to clear all customer data. This includes music files, eBooks and navigation addresses. This does not clear Nav database data. |