LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2017 >> Spark LT, Automatic CVT Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 82 (Parking Assistance Systems) >> Diagnostic Information and Procedures >> DTC B1405 (UD5/UDP/UDQ) >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2019 Buick Cascada, 2018 Buick Cascada, and 2017 Buick Cascada. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF, disconnect the X2 and X3 harness connectors at the K182 Parking Assist Control Module.
  2. Test for infinite resistance between the Parking Assist Sensor Reference Voltage circuit terminal 4 X2 and ground.
    • If less than infinite resistance 
    1. Ignition OFF, disconnect the harness connector at each of the B306 Parking Assist Sensors.
    2. Test for infinite resistance between the Parking Assist Sensor Reference Voltage circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If less than 2 Ω, replace the appropriate B306 Parking Assist Sensor.
    • Go to next step: If infinite resistance 
  3. Test for infinite resistance between the Parking Assist Sensor Reference Voltage circuit terminal 1 X3 and ground.
    • If less than infinite resistance 
    1. Ignition OFF, disconnect the harness connector at each of the B306 Parking Assist Sensors.
    2. Test for infinite resistance between the Parking Assist Sensor Reference Voltage circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If less than 2 Ω, replace the appropriate B306 Parking Assist Sensor.
    • Go to next step: If infinite resistance 
  4. Ignition ON.
  5. Test for less than 1 V between the Parking Assist Sensor Reference Voltage circuit terminal 4 X2 and ground.
    • If greater than 1 V 
    1. Ignition OFF, disconnect the harness connector at each of the B306 Parking Assist Sensors.
    2. Test for less than 1 V between the Parking Assist Sensor Reference Voltage circuit and ground.
      • If greater than 1 V, repair the short to voltage on the circuit.
      • If less than 1 V, replace the appropriate B306 Parking Assist Sensor.
    • Go to next step: If less than 1 V 
  6. Test for less than 1 V between the Parking Assist Sensor Reference Voltage circuit terminal 1 X3 and ground.
    • If greater than 1 V 
    1. Ignition OFF, disconnect the harness connector at each of the B306 Parking Assist Sensors.
    2. Test for less than 1 V between the Parking Assist Sensor Reference Voltage circuit and ground.
      • If greater than 1 V, repair the short to voltage on the circuit.
      • If less than 1 V, replace the appropriate B306 Parking Assist Sensor.
    • Go to next step: If less than 1 V 
  7. Connect the X2 and X3 harness connector at the K182 Parking Assist Control Module, ignition ON.
  8. Verify DTC B1405 is not set.
    • If DTC B1405 is set 
    1. Ignition OFF, disconnect the harness connector at each of the B306 Object Sensors.
    2. Verify DTC B1405 is not set.
      • If DTC B1405 is set

        Replace the K182 Parking Assist Control Module.

      • Go to next step: If DTC B1405 is not set.
    3. Verify the DTC B1405 does not set while connecting the harness connector at each B306 Object Sensor, one at a time.
    • If DTC B1405 does set

      Replace the B306 Object Sensor that was connected immediately before DTC B1405.

    • Go to next step: If DTC B1405 does not set.
  9. All OK.
    • Go to next step: If DTC B1405 is not set. 
  10. All OK.
scientia non olet · About LEMON Manuals