LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2017 >> Spark LT, Automatic CVT Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 65 (Power Door Lock System And Vehicle Access System) >> Diagnostic Information and Procedures >> DTC B3125, B3130, or B3135 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2019 Buick Cascada, 2018 Buick Cascada, and 2017 Buick Cascada. However, it is still accessible from the selected car via links, so may be relevant.

Test 1

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A23D Door Latch Assembly - Driver
  3. Connect a test lamp between the test points: Control circuit terminal 2 & Control circuit terminal 3
  4. Ignition - On / Vehicle - In Service Mode
  5. Operate the component: S48A Multifunction Switch - Instrument Panel - Lock Switch & Unlock Switch

    Verify the test lamp does not turn On and Off.

    • If the test lamp turns On and Off 

      Test or replace the component: A23D Door Latch Assembly - Driver

    • Go to next step: If the test lamp does not turn On and Off 
  6. Ignition/Vehicle - Off
  7. Disconnect the electrical connector: X6@K9 Body Control Module
  8. Test for less than 2 ohms between the test points:
    • Control circuit terminal 2@Component harness & Terminal 4 X6@Control module harness
    • Control circuit terminal 3@Component harness & Terminal 1 X6@Control module harness
    • If 2 ohms or greater 
    • Repair the open/high resistance in the circuit.
    • Go to next step: If less than 2 ohms 
  9. Test or replace the component: K9 Body Control Module

Test 2

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A23P Door Latch Assembly - Passenger
  3. Connect a test lamp between the test points: Control circuit terminal 7 & Control circuit terminal 8
  4. Ignition - On / Vehicle - In Service Mode
  5. Operate the component: S48A Multifunction Switch - Instrument Panel - Lock Switch & Unlock Switch

    Verify the test lamp does not turn On and Off.

    • If the test lamp turns On and Off 

      Test or replace the component: A23P Door Latch Assembly - Passenger

    • Go to next step: If the test lamp does not turn On and Off 
  6. Ignition/Vehicle - Off
  7. Disconnect the electrical connector: X6@K9 Body Control Module
  8. Ignition - On / Vehicle - In Service Mode
  9. Test for less than 2 ohms between the test points:
    • Control circuit terminal 8@Component harness & Terminal 2 X6@Control module harness
    • Control circuit terminal 7@Component harness & Terminal 4 X6@Control module harness
    • If 2 ohms or greater 
    • Repair the open/high resistance in the circuit.
    • Go to next step: If less than 2 ohms 
  10. Test or replace the component: K9 Body Control Module

Test 3

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: X2 & X6@K9 Body Control Module
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 3 X6 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 3 X6 & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On / Vehicle - In Service Mode
  5. Verify a test lamp turns On between the test points: B+ circuit terminal 4 X2 & Ground
    • If the test lamp does not turn On and the circuit fuse is OK 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Test for less than 2 ohms between the test points: B+ circuit terminal 4 X2 & Output terminal @Fuse
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not turn On and the circuit fuse is open 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the electrical connector:
      • A23D Door Latch Assembly - Driver
      • A23P Door Latch Assembly - Passenger
    3. Test for infinite resistance between the test points:
      • Control circuit terminal 1 X6@K9 Body Control Module & Ground
      • Control circuit terminal 2 X6@K9 Body Control Module & Ground
      • Control circuit terminal 4 X6@K9 Body Control Module & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: A23 Door Latch Assembly
    • Go to next step: If the test lamp turns On 
  6. Ignition/Vehicle - Off
  7. Connect the electrical connector: X2@K9 Body Control Module
  8. Ignition - On / Vehicle - In Service Mode
  9. Test for less than 1 V between the test points:
    • Control circuit terminal 1 X6@K9 Body Control Module & Ground
    • Control circuit terminal 2 X6@K9 Body Control Module & Ground
    • Control circuit terminal 4 X6@K9 Body Control Module & Ground
    • If greater than 1 V 

      Repair the short to voltage on the circuit.

    • Go to next step: If 1 V or less 
  10. Ignition/Vehicle - Off
  11. Test for infinite resistance between the test points:
    • Control circuit terminal 1 X6@K9 Body Control Module & Ground
    • Control circuit terminal 2 X6@K9 Body Control Module & Ground
    • Control circuit terminal 4 X6@K9 Body Control Module & Ground
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  12. Replace the component: K9 Bod y Control Module
scientia non olet · About LEMON Manuals