Fastener Specifications (Off Vehicle)
WARNING: This page is about a different car, the 2019 Buick Cascada, 2018 Buick Cascada, and 2017 Buick Cascada. However, it is still accessible from the selected car via links, so may be relevant.
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| 1-2-3-4 Clutch Fluid Passage Seal |
| Control Solenoid Valve Assembly Filter Plate |
| Control Valve Body Gasket |
| Control Valve Body Cover Wiring Connector Hole Seal |
| Automatic Transmission Fluid Pump Seal |
| Input Speed Sensor Assembly Seal |
| Low and Reverse Clutch Fluid Passage Seal |
| Manual Shaft Detent Lever Hub Pin |
| Manual Shift Shaft Pin |
| Park Pawl Actuator Guide Pin |
| Park Pawl Actuator Guide Assembly Seal |
| Torque Converter Housing Gasket |
| Turbine Shaft Retainer Ring |
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
||||
|---|---|---|---|---|
| Application | Reference number from Disassembled Views | Quantity | Size | Specification |
| Metric (English) | ||||
| Automatic Transmission Auxiliary Fluid Accumulator Bolt | 377 | 5 | M8 x 30 | 22 N.m (16 lb ft) |
| Automatic Transmission Fluid Pump Bolt@Torque Converter Housing | ||||
|
200 | 7 - 6T30, 8 - 6T40/45/50 | M8 x 33 | 10 N.m (89 lb in) |
|
45 Degrees | |||
| Automatic Transmission Fluid Pump Cover Bolt | 302 | 3 - 6T30, 2 - 6T40/45/50 | M6 x 25 | 12 N.m (106 lb in) |
| Automatic Transmission Fluid Pump Cover Bolt | 320 | 20 - 6T30 | M6 x 21.5 | 12 N.m (106 lb in) |
| Control Valve Body Bolt@Transmission Case | 4 | 12 | M6 x 97 | 11 N.m (97 lb in) |
| Control Valve Body Bolt@Transmission Case | 6 | 3 | M5 x 40.5 | 7 N.m (62 lb in) |
| Control Valve Body Bolt | 400 | 1 | M5 x 40.5 | 7 N.m (62 lb in) |
| Control Valve Body Bolt@Transmission Case | 9 | 2 | M6 x 53 | 11 N.m (97 lb in) |
| Control Valve Body Bolt@Transmission Case | 10 | 9 | M6 x 60 | 11 N.m (97 lb in) |
| Control Valve Body Cover Bolt | 1 | 13 | M6 x 30 | 12 N.m (106 lb in) |
| Drain Plug | 64 | 1 | 1/8"-27 NPTF | 12 N.m (106 lb in) |
| Automatic Transmission Fluid Level Hole Plug | 63 | 1 | 1/8"-27 NPTF | 12 N.m (106 lb in) |
| Fluid Pressure Test Hole Plug | 51 | 1 | 1/8"-27 NPTF | 12 N.m (106 lb in) |
| Front Differential Carrier Baffle Bolt@Torque Converter Housing | 204 | 2 | M6 x 25 | 12 N.m (106 lb in) |
| Front Differential Carrier Baffle Bolt@ Transmission Case | 61 | 2 | M6 x 18.5 - 6T30, M6 x 16 - 6T40/45/50 | 12 N.m (106 lb in) |
| Input Shaft Support Bolt | 57 | 3 | M6 x 50 | 12 N.m (106 lb in) |
| Input Speed Sensor Bolt | 21 | 1 | M6 x 23 | 9 N.m (80 lb in) |
| Manual Shift Detent Spring Bolt | 17 | 1 | M6 x 16 | 12 N.m (106 lb in) |
| Output Speed Sensor Bolt | 15 | 1 | M6 x 18 | 9 N.m (80 lb in) |
| Torque Converter and Differential Housing Bolt | ||||
|
27 | 14 - 6T30, 15 - 6T40/45/50 | M8 x 30 | 10 N.m (89 lb in) |
|
50 Degrees | |||