LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2017 >> Spark LT, Automatic CVT Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 53 (Lighting System - Diagnostic Information And Procedures) >> Diagnostic Information and Procedures >> Park, License, and/or Tail Lamps Malfunction >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2019 Buick Cascada, 2018 Buick Cascada, and 2017 Buick Cascada. However, it is still accessible from the selected car via links, so may be relevant.

Park Lamp Switch Malfunction

  1. Ignition OFF, scan tool disconnected, all doors closed, all accessories OFF, disconnect the harness connector at the S30 Headlamp Switch. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 6 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Ignition ON.
  4. Verify the scan tool Park Lamps Switch parameter is Inactive.
    • If not Inactive 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit terminal 3 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • Go to next step: If Inactive 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 3 and ground.
  6. Verify the scan tool Park Lamps Switch parameter is Active.
    • If not Active 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 3 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If Active 
  7. Test or replace the S30 Headlamp Switch.

Side Marker Lamps Malfunction

  1. Ignition OFF, exterior lamps OFF, disconnect the harness connector at the appropriate E2 Side Marker Lamp.
  2. Test for less than 5 Ω between the ground circuit terminal 2 and ground.
    • If 5 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 5 Ω 
  3. Connect a test lamp between the control circuit terminal 1 and ground, ignition ON.
  4. Verify the test lamp turns ON and OFF when commanding the side marker lamps ON and OFF with the park lamp switch.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If the test lamp turns ON and OFF 
  5. Test or replace the E2 Side Marker Lamp.

Tail Lamps Malfunction

  1. Ignition OFF, exterior lamps OFF, disconnect the harness connector at the appropriate tail lamp assembly listed below.
    • E51L Tail Lamp Assembly - Auxiliary Left
    • E51R Tail Lamp Assembly - Auxiliary Right
    • E43L Liftgate Tail Lamp Assembly - Left
    • E43R Liftgate Tail Lamp Assembly - Right
  2. Test for less than 10 Ω between the ground circuit terminal A and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Connect a test lamp between the control circuit terminal B and ground, ignition ON.
  4. Verify the test lamp turns ON and OFF when commanding the appropriate E5 Tail Lamp ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X3 harness connector at the K23 Folding Top Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K23 Folding Top Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X3 harness connector at the K23 Folding Top Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K23 Folding Top Control Module.
    • Go to next step: If the test lamp turns ON and OFF 
  5. Test or replace the appropriate E5 Tail Lamp.

License Plate Lamps Malfunction

  1. Ignition OFF, exterior lamps OFF, remove both E7 License Plate Lamp bulbs.
  2. Test for less than 10 Ω between each ground circuit terminal 2 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Connect a test lamp between the E7L License Plate Lamp - Left control circuit terminal 1 and ground, ignition ON.
  4. Verify the test lamp turns ON and OFF when commanding the License Plate Lamps ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If the test lamp turns ON and OFF 
  5. Ignition OFF.
  6. Connect a test lamp between the E7R License Plate Lamp - Right control circuit terminal 1 and ground, ignition ON.
  7. Verify the test lamp turns ON and OFF when commanding the License Plate Lamps ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the X4 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
    • Go to next step: If the test lamp turns ON and OFF 
  8. Test or replace the E7 License Plate Lamp.
scientia non olet · About LEMON Manuals