Circuit/System Testing

DTC C0277 06, C0277 07, C0890 03, and C0890 07

1. Ignition OFF, disconnect the harness connector at the B22 Brake Pedal Position Sensor, ignition ON.
2. Test for 4.8 - 5.2 V between the 5 V reference circuit terminal 1 and ground.
   • If less than 4.8 V 
   1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module.
   2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
   3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
   • If greater than 5.2 V 
   1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module, ignition ON.
   2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
   • Go to next step: If between 4.8 - 5.2 V 
3. Verify the scan tool Brake Pedal Applied parameter is Inactive.
   • If not Inactive 
   1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module, ignition ON.
   2. Test for less than 1 V between the signal circuit terminal 3 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
   • Go to next step: If Inactive 
4. Install a 3 A fused jumper wire between the 5-volt reference terminal 1 and signal circuit terminal 3.
5. Verify the scan tool Brake Pedal Applied parameter is Active.
   • If not Active 
   1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module.
   2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
   3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
   • Go to next step: If Active 
6. Test or replace the B22 Brake Pedal Position Sensor.

DTC C0277 4B

1. Verify DTC C0277 4B is not set.
   • If DTC C0277 4B is set 
   1. Ignition ON
   2. Perform the brake pedal position sensor learn procedure for the K9 Body Control Module. Refer to Brake Pedal Position Sensor Calibration .
   3. Verify the DTC does not reset while operating the vehicle under the conditions for running the DTC.
      • If the DTC resets, replace the B22 Brake Pedal Position sensor.
      • Go to next step: If the DTC does not reset
   4. All OK.
   • Go to next step: If DTC C0277 4B is not set 
2. All OK.

DTC C0277 09 and DTC C0277 12

1. Verify DTC C0277 09 and C0277 12 are not set.
   • If DTC C0277 09 or C0277 12 is set 
   1. Replace the B22 Brake Pedal Position sensor.
   2. Perform the brake pedal position sensor learn procedure for the K9 Body Control Module. Refer to Brake Pedal Position Sensor Calibration .
   3. Verify the DTC does not reset while operating the vehicle under the conditions for running the DTC.
      • If the DTC resets, replace the K9 Body Control Module.
      • Go to next step: If the DTC does not reset
   4. All OK.
   • Go to next step: If DTC C0277 09 or C0277 12 is not set 
2. All OK.