LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2017 >> Spark LT, Automatic CVT Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 53 (Lighting System - Diagnostic Information And Procedures) >> Diagnostic Information and Procedures >> DTC B3415 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2019 Buick Cascada, 2018 Buick Cascada, and 2017 Buick Cascada. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF, disconnect the harness connector at the appropriate B51 Suspension Height Sensor, ignition ON.
  2. Verify a test lamp illuminates between the low reference circuit terminal 1 and B+.
    • If the test lamp does not illuminate 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • Go to next step: If the test lamp illuminates 
  3. Ignition ON.
  4. Test for 4.8 - 5.2 V between the 5 V reference circuit terminal 3 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module, ignition ON.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K26 Headlamp Control Module.
    • Go to next step: If between 4.8 - 5.2 V 
  5. Verify the appropriate scan tool Suspension Manually Entered Trim Height parameter is less than 1 mm.
    • If 1 mm or greater 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 2 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K26 Headlamp Control Module.
    • Go to next step: If less than 1 mm 
  6. Install a 3 A fused jumper wire between the 5 V reference circuit terminal 3 and the signal circuit terminal 2, engine RUNNING.
  7. Verify the appropriate scan tool Suspension Manually Entered Trim Height parameter is greater than 0 mm.
    • If not greater than 0 mm 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for infinite resistance between the signal circuit terminal 2 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • Go to next step: If greater than 0 mm 
  8. Test or replace the appropriate B51 Suspension Height Sensor.
scientia non olet · About LEMON Manuals