Fastener Specifications

WARNING: This page is about a different variant/trim than selected.

Single Use Non-Threaded Fasteners/Components

NOTE: All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal.
Application
Camshaft Cover Gasket
Camshaft Position Actuator Solenoid Valve Solenoid Seal
Catalytic Converter Gasket
Crankshaft Front Oil Seal
Crankshaft Rear Oil Seal
Cylinder Head Gasket
Engine Coolant Thermostat Housing Seal
Engine Oil Cooler Fitting Gasket
Engine Oil Cooler Housing Seal
Engine Oil Cooler Seal
Engine Oil Pressure Sensor Seal
Exhaust Gas Recirculation Cooler Gasket
Exhaust Gas Recirculation Cooler Inlet Pipe Gasket
Exhaust Gas Recirculation Cooler Inlet Pipe Seal Ring
Exhaust Gas Recirculation Cooler Outlet Pipe Gasket
Exhaust Gas Recirculation Pipe Gasket
Fuel Injection Pump Gasket
Fuel Injector O-Ring Seal
Intake Manifold Gasket
Oil Filter Adapter Gasket
Oil Filter Cap Seal
Oil Level Indicator Tube O-Ring
Oil Pump Flow Control Valve Seal
Oil Pump Seal
Oil Pump Suction Pipe Gasket
Throttle Body Gasket
Water Outlet Gasket
Water Pump Inlet Pipe Seal
Water Pump Seal

Single Use Threaded Fastener/Component Tightening Specifications

NOTE: All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal.
Application	Specification
Application	Metric (English)
Automatic Transmission Flex Plate Bolt
First Pass:	30 N.m (22 lb ft)
Final Pass:	70 degrees
Camshaft Position Actuator Adjuster Bolt
First Pass:	65 N.m (48 lb ft)
Final Pass:	120 - 135 degrees
Connecting Rod Bearing Cap Bolt
First Pass:	45 N.m (33 lb ft)
Final Pass:	60 degrees
Crankshaft Balancer Bolt
First Pass:	250 N.m (184 lb ft)
Final Pass:	45 degrees
Cylinder Head Bolt
First Pass:	25 N.m (18 lb ft)
Second Pass:	90 degrees
Third Pass:	90 degrees
Fourth Pass:	90 degrees
Final Pass:	15 degrees
Engine Mount Bolt
First Pass:	100 N.m (74 lb ft)
Final Pass:	60 - 75 degrees
Engine Mount Bracket Bolt
First Pass:	58 N.m (43 lb ft)
Final Pass:	60 - 75 degrees
Engine Mount to Engine Mount Bracket Bolts
First Pass:	100 N.m (74 lb ft)
Final Pass:	60 - 70 degrees
Engine Oil Cooler Fitting	25 N.m (18 lb ft)
Fuel Injector Bolt	5 N.m (44 lb in)
Lower Crankcase Bolt to Engine Block - M10
First Pass:	50 N.m (37 lb ft)
Final Pass:	120 degrees

Reusable Threaded Fastener Tightening Specifications

NOTE: All fasteners listed in this table can be reused after removal.
Application	Specification
Application	Metric (English)
Air Conditioning Compressor Bracket Bolt	22 N.m (16 lb ft)
Air Conditioning Compressor Hose Bolt	10 N.m (89 lb in)
Camshaft Bearing Cap Bolt	10 N.m (89 lb in)
Camshaft Cover Bolt	9 N.m (80 lb in)
Camshaft Cover Stud	9 N.m (80 lb in)
Camshaft Position Actuator Solenoid Valve Solenoid Bolt	10 N.m (89 lb in)
Catalytic Converter Brace Bracket Nut	22 N.m (16 lb ft)
Catalytic Converter Heat Shield Bolt	9 N.m (80 lb in)
Catalytic Converter Heat Shield Nut	9 N.m (80 lb in)
Catalytic Converter Nut	22 N.m (16 lb ft)
Crankshaft Position Sensor Bolt	10 N.m (89 lb in)
Crankshaft Rear Oil Seal Housing Bolt	10 N.m (89 lb in)
Cylinder Head Oil Gallery Plug	15 N.m (11 lb ft)
Engine Coolant Thermostat Housing Bolt	10 N.m (89 lb in)
Engine Coolant Heater Hole Plug	60 N.m (44 lb ft)
Engine Lift Bracket Bolt	22 N.m (16 lb ft)
Engine Mount Brace Bolt	22 N.m (16 lb ft)
Engine Mount Brace Nut	22 N.m (16 lb ft)
Engine Oil Cooler Bolt	10 N.m (89 lb in)
Engine Oil Cooler Mounting Plate Bolt	25 N.m (18 lb ft)
Engine Oil Pressure Sensor Seal	35 N.m (26 lb ft)
Engine Wiring Harness Bracket Nut	10 N.m (89 lb in)
Engine Wiring Harness Clip Nut	10 N.m (89 lb in)
Engine Wiring Harness Ground Nut	10 N.m (89 lb in)
Evaporative Emission Canister Purge Solenoid Valve Bolt	9 N.m (80 lb in)
Exhaust Gas Recirculation Cooler Bolt	25 N.m (18 lb ft)
Exhaust Gas Recirculation Cooler Inlet Pipe Bolt	10 N.m (89 lb in)
Exhaust Gas Recirculation Cooler Inlet Pipe Bolt	10 N.m (89 lb in)
Exhaust Gas Recirculation Cooler Temperature Sensor	45 N.m (33 lb ft)
Exhaust Gas Recirculation Pipe Bolt	10 N.m (89 lb in)
Exhaust Gas Recirculation Valve Bolt	25 N.m (18 lb ft)
Fuel Injection Fuel Feed Front Pipe Bracket Bolt	10 N.m (89 lb in)
Fuel Injection Fuel Feed Front Pipe Nut	30 N.m (22 lb ft)
Fuel Injection Fuel Rail Pressure Sensor	30 N.m (22 lb ft)
Fuel Injection Pump Bolt	11 N.m (97 lb in)
Fuel Rail Bolt	10 N.m (89 lb in)
Ground Cable Nut	10 N.m (89 lb in)
Heated Oxygen Sensor	42 N.m (31 lb ft)
Ignition Coil Bolt	10 N.m (89 lb in)
Intake Manifold Bolt	25 N.m (18 lb ft)
Intake Manifold Brace Bolt	10 N.m (89 lb in)
Intake Manifold Cover Bolt	4 N.m (35 lb in)
Intake Manifold Mount	9 N.m (80 lb in)
Knock Sensor Bolt	22 N.m (16 lb ft)
Lower Crankcase Bolt to Engine Block - M8	25 N.m (18 lb ft)
Lower Engine Front Cover Bolt - M6	10 N.m (89 lb in)
Lower Engine Front Cover Bolt - M8	25 N.m (18 lb ft)
Lower Engine Front Cover Bolt - M10	58 N.m (43 lb ft)
Manifold Absolute Pressure Sensor Bolt	5 N.m (44 lb in)
Oil Pan Drain Plug	14 N.m (124 lb in)
Oil Filter Cap	25 N.m (18 lb ft)
Oil Filter Housing Bolt	25 N.m (18 lb ft)
Oil Flow Check Valve	10 N.m (89 lb in)
Oil Level Indicator Tube Bolt	10 N.m (89 lb in)
Oil Pan Baffle Bolt	10 N.m (89 lb in)
Oil Pan Bolt	10 N.m (89 lb in)
Oil Pump Bolt	10 N.m (89 lb in)
Oil Pump Flow Control Valve Bolt	10 N.m (89 lb in)
Oil Pump Suction Pipe Bolt	10 N.m (89 lb in)
Piston Oil Nozzle Bolt	10 N.m (89 lb in)
Throttle Body Bolt	9 N.m (80 lb in)
Timing Chain Guide Bolt	7 N.m (62 lb in)
Timing Chain Guide Pin	19 N.m (14 lb ft)
Timing Chain Tensioner Bolt	10 N.m (89 lb in)
Timing Chain Upper Guide Bolt	7 N.m (62 lb in)
Upper Engine Front Cover Bolt - M6	10 N.m (89 lb in)
Upper Engine Front Cover Bolt - M10	35 N.m (26 lb ft)
Water Outlet Bolt	10 N.m (89 lb in)
Water Pump Bolt	10 N.m (89 lb in)
Water Pump Inlet Pipe Bolt	25 N.m (18 lb ft)
Water Pump Pulley Bolt	10 N.m (89 lb in)