LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2016 >> Spark LT, Automatic CVT Trans >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel System Displays And Gauges >> Diagnostic Information and Procedures >> DTC P0521, P0522, or P0523: Engine Oil Pressure Sensor >> Circuit/System Testing

Circuit/System Testing

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems » Off
  2. Disconnect the electrical connector: B37B Engine Oil Pressure Sensor
  3. Test for less than 10 Ω between the test points: Low Reference circuit terminal 2G &Ground
    • If 10 Ω or greater 
    1. Disconnect the electrical connector: K20 Engine Control Module
    2. Test for less than 2 Ω between the test points: Low Reference circuit terminal 2@Component harness &The other end of the circuit
      • If 2Ω or greater » Repair the open/high resistance in the circuit.
      • If less than 2Ω» Replace the component:K20 Engine Control Module
    • If less than 10 Ω 
  4. Ignition » On / Vehicle » In Service Mode
  5. Test for 4.8 to 5.2 V between the test points: 5V Reference circuit terminal 3 &Low Reference circuit terminal 2
    • If less than 4.8 V 
    1. Ignition/Vehicle » Off
    2. Disconnect the electrical connector:K20 Engine Control Module
    3. Test for infinite resistance between the test points: 5V Reference circuit terminal 3V @ Component harness &Ground
      • If less than infinite resistance » Repair the short to ground on the circuit.
      • If infinite resistance
    4. Test for less than 2 Ω between the test points: 5 V Reference circuit terminal 3V @ Component harness &The other end of the circuit
      • If 2 Ω or greater » Repair the open/high resistance in the circuit.
      • If less than 2 Ω » Replace the component:K20 Engine Control Module
    • If greater than 5.2 V 
    1. Ignition/Vehicle » Off
    2. Disconnect the electrical connector:K20 Engine Control Module
    3. Ignition » On / Vehicle » In Service Mode
    4. Test for less than 1 V between the test points: 5V Reference circuit terminal 3V @Component harness& Ground
      • If 1 V or greater » Repair the short to voltage on the circuit.
      • If less than 1 V » Replace the component:K20 Engine Control Module
    • If between 4.8 and 5.2 V 
  6. Verify the scan tool parameter:Engine Oil Pressure Sensor = 0 kPa (0 PSI)
    • If greater than 0 kPa (0 PSI) 
    1. Ignition/Vehicle » Off
    2. Disconnect the electrical connector:K20 Engine Control Module
    3. Ignition » On / Vehicle » In Service Mode
    4. Test for less than 1 V between the test points:Signal circuit terminal 1 @Component harness& Ground
      • If 1 V or greater » Repair the short to voltage on the circuit.
      • If less than 1 V » Replace the component:K20 Engine Control Module
    • If 0 kPa (0 PSI) or less 
  7. Connect a 3 A fused jumper wire between the test points:Signal circuit terminal 3 &1 V Reference circuit terminal 5
  8. Verify the scan tool parameter:Engine Oil Pressure Sensor =Greater than 800 kPa (116 PSI)
    • If 800 kPa (116 PSI) or less 
    1. Ignition/Vehicle » Off & Remove » Jumper wire(s)
    2. Disconnect the electrical connector:K20 Engine Control Module
    3. Test for infinite resistance between the test points:Signal circuit terminal 1@Component harness& Ground
      • If less than infinite resistance » Repair the short to ground on the circuit.
      • If infinite resistance
    4. Test for less than 2Ω between the test points:Signal circuit terminal 1@Component harness&The other end of the circuit
      • If 2Ω or greater » Repair the open/high resistance in the circuit.
      • If less than 2Ω » Replace the component:K20 Engine Control Module
    • If greater than 800 kPa (116 PSI) 
  9. Test or replace the component:B37B Engine Oil Pressure Sensor
scientia non olet · About LEMON Manuals