LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Inflatable Restraint System >> Diagnostic Information and Procedures >> Airbag Indicator Malfunction (Passenger) >> Circuit/System Testing

Circuit/System Testing

NOTE:

When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected:

  • Passenger air bag disable on/off indicator.
  • Passenger air bag disable on/off indicator wiring harness.
  1. Ignition OFF, disconnect the harness connector at the P14 Passenger Air Bag Disable Indicator.
  2. Test for less than 10 Ω between the ground circuit terminal 4 and ground.
    • If 10 Ω or greater 
    1. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON, command the passenger air bag OFF indictor OFF with a scan tool.
  4. Test for less than 11 V between the control circuit terminal 5 and ground.
    • If 11 V or greater 
    1. Ignition OFF, disconnect the X1 harness connector at the K36 Inflatable Restraint Sensing and Diagnostic Module. Ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K36 Inflatable Restraint Sensing and Diagnostic Module.
    • If less than 11 V 
  5. Command the passenger air bag OFF indicator ON with a scan tool.
  6. Test for greater than 4 V between the control circuit terminal 5 and ground.
    • If 4 V or less 
    1. Ignition OFF, disconnect the X1 harness connector at the K36 Inflatable Restraint Sensing and Diagnostic Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
    3. Test for less than 2 Ω in each control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K36 Inflatable Restraint Sensing and Diagnostic Module.
    • If greater than 4 V 
  7. Command the passenger air bag ON indicator OFF with a scan tool.
  8. Test for less than 11 V between the control circuit terminal 2 and ground.
    • If 11 V or greater 
    1. Ignition OFF, disconnect the X1 harness connector at the K36 Inflatable Restraint Sensing and Diagnostic Module. Ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K36 Inflatable Restraint Sensing and Diagnostic Module.
    • If less than 11 V 
  9. Command the passenger air bag ON indicator ON with a scan tool.
  10. Test for greater than 4 V between the control circuit terminal 2 and ground.
    • If 4 V or less 
    1. Ignition OFF, disconnect the X1 harness connector at the K36 Inflatable Restraint Sensing and Diagnostic Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
    3. Test for less than 2 Ω in each control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K36 Inflatable Restraint Sensing and Diagnostic Module.
    • If greater than 4 V 
  11. Replace the P14 Passenger Air Bag Disable Indicator.
scientia non olet · About LEMON Manuals