LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2015 >> Cruze LT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 12 (Engine Controls And Fuel - 2.0L (LUZ) Diesel - DTC P0430 To DTC P2080) >> Diagnostic Information and Procedures >> DTC P204C or P204D: Reductant Pressure Sensor Circuit >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different variant/trim than selected.
  1. Ignition Off and all vehicle systems Off, disconnect the harness connector at the B194 Reductant Pressure Sensor. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 5 Ω between the low reference circuit terminal 3 and ground.
    • If 5 Ω or greater 
    1. Disconnect the harness connector at the K20 Engine Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
      • If less than 5 Ω 
  3. Ignition On.
  4. Test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition Off, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
      • If greater than 5.2 V 
    1. Ignition Off, disconnect the harness connector at the K20 Engine Control Module.
    2. Ignition On.
    3. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit
      • If less than 1 V, replace the K20 Engine Control Module.
      • If between 4.8-5.2 V 
  5. Verify the scan tool Reductant Pressure Sensor parameter is 0 kPa (0 psi).
    • If greater than the specified value 
    1. Ignition Off, disconnect the harness connector at the K20 Engine Control Module.
    2. Ignition On.
    3. Test for less than 1 V between the signal circuit terminal 2 and ground.
    • If 1 V or greater, repair the short to voltage on the circuit.
    • If less than 1 V, replace the K20 Engine Control Module.
    • If equal to the specified value 
  6. Install a 3 A fused jumper wire between the signal circuit terminal 2 and the 5 V reference circuit terminal 1.
  7. Verify the scan tool Reductant Pressure Sensor parameter should be greater than 700 kPa (102 psi).
    • If less than the specified value 
    1. Ignition Off, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit terminal and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
    • If 2 Ω or greater, repair the open/high resistance in the circuit.
    • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than the specified value 
  8. Replace the B194 Reductant Pressure Sensor.
scientia non olet · About LEMON Manuals